Metric Spacers | McMaster-Carr

Compared to our general purpose washers, these have exaggerated diameters and/or thicknesses. Use them to cover oversized holes, hold heavy fastening loads, or as spacers and levelers.

Metric General Purpose Washers

Use these metric washers to evenly distribute the load under bolt or screw heads and nuts when fastening. They can also act as spacers.

Metric Washers for
Structural Applications

These thick washers are designed to support structural screws, studs, and nuts.

Metric Plastic Washers

Metric Chemical-Resistant
Plastic Washers

These metric washers surpass most other plastic washers when it comes to withstanding chemicals, oil, and grease.

Metric Electrical-Insulating
Plastic Washers

Metric Water- and
Steam-Resistant Plastic Washers

Low moisture absorption and good heat resistance make these metric washers suitable for wet and harsh environments.

Metric High-Temperature
Plastic Washers

These metric washers can withstand temperatures up to 450° or 500° F without degrading.

Metric Extreme-Temperature
Ceramic Washers

These metric washers hold up in blistering temperatures up to 3000° F.

Square Washers

Square washers fit into slots and channels and have flat sides to keep them from rotating.

Metric Countersunk Washers

Flat and oval head screws sit flush within these metric washers for a neat, finished appearance.

Plastic Countersunk Washers

Plastic washers are good electrical insulators.

Metric Finishing
Countersunk Washers

Sleeve Washers for Soft Material

Reinforce holes in soft material to keep them from collapsing around screws.

Self-Retaining Washers

A specially shaped ID grips your screw shank tightly.

Clipped Washers

Clipped to fit where standard washers can't, these won't rotate when you position the flat edge against a flat surface.

Oversized Clipped Washers

With greater diameters and/or thicknesses than general purpose washers, these washers cover oversized holes or act as spacers and levelers. Clipped to fit where standard washers can’t, they won’t rotate when you position the flat edge against a flat surface.

Lock Washers

Metric Split Lock Washers

As you tighten a bolt, these metric washers flatten to add tension to the threaded joint and prevent loosening from small amounts of vibration.

Metric Split Lock Washers
for Socket Head Screws

Metric External-Tooth Lock Washers

Teeth on the outside edge of these metric washers bite into the screw head and joint for a tight grip.

Tight-Grip External-Tooth
Lock Washers

The teeth on these washers bite further into the screw head and joint than standard external-tooth washers to provide a stronger hold.

Metric Internal-Tooth Lock Washers

Internal teeth dig into the screw head while the smooth outside edge won't snag objects. Use with metric fasteners that have small heads, such as fillister and cheese head screws.

Internal-/External-Tooth
Lock Washers

The combination of internal and external teeth boosts gripping power to maintain a tight hold and provide more vibration resistance than other tooth lock washers. Use with fasteners that have heads large enough to make contact with the external teeth, such as pan, button, and binding head screws.

Metric Spring Lock Washers

The arched shape of these washers presses up against a bolt and down against a nut to prevent loosening from wear, vibration, or temperature changes.

Spring Lock Washers
for Slotted Bearing Nuts

Designed for use with bearing nuts, these lock washers have a conical shape that presses like a spring against bearings, bushings, gears, and pulleys to hold them in place on your threaded shaft or spindle.

Belleville Spring Lock Washers
for Socket Head Screws

These washers have smaller outside diameters than standard spring lock washers to fit neatly under socket head cap screws.

Spring Lock Washers
for Plastic Screws

Designed for use with plastic screws, these acetal washers are good electrical insulators. They are excellent for use under water and in rotating assemblies.

Wedge Lock Washers

Also known as NORD-LOCK® washers, these two-piece washers provide more locking power than split, tooth, and spring lock washers. Wedges on the inside lock the two pieces together, and serrations on the exterior grip surfaces to resist loosening from high vibration and shifting.

Metric Tab Lock Washers

Bend the tab of these metric lock washers against the flats of a hex nut or bolt head to prevent the fastener and washer from turning and loosening due to vibration, wear, or changes in temperature.

Abrasion-Resistant Leather Washers

These leather washers are nonmarring.

Sealing Washers

Pressure-Rated Metal-Bonded
Sealing Washers

These washers are rated to withstand pressure up to 100 psi.

Metric High-Pressure-Rated
Metal-Bonded Sealing Washers

Able to withstand pressure greater than 7,000 psi, these one-piece bonded washers create the tightest seals.

Metal Sealing Washers

Also known as crush washers, these compress when tightened to form a tighter, more durable seal than rubber washers. They are commonly used to seal fluids such as oil and fuel.

Leveling and Wave Washers

Metric Leveling Washers

Triple-Wave Washers

With three points of surface contact, these washers provide more stability than single-wave washers.

Metric Single-Wave Washers

These curved, flexible washers act like springs to compensate for tolerance variations and uneven surfaces.

Metric Leveling Washers for I-Beams

Thread Adapters

Metric-to-Metric Male-Female
Hex Thread Adapters

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Inch-to-Metric Male-Female
Hex Thread Adapters

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

Male-Female Round Universal
Thread Adapters with Through Hole

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Metric-to-Metric Male
Hex Thread Adapters

Twist these adapters onto female metric threads to change pitch or switch thread sizes.

Metric-to-Metric Male
Round Thread Adapters

Inch-to-Metric Male
Hex Thread Adapters

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Inch-to-Metric Male
Round Thread Adapters

Male Round Universal Thread
Adapters with Through Hole

Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Shims

Ring Shims

Precisely align, level, and adjust spacing on fasteners and shafts with these shims.

Shims for Shortening
Screw Shoulders

Slide these shims under the screw head to shorten the shoulder length.

Shims for Lengthening
Screw Shoulders

Spin these shims onto screw threads to extend the shoulder length.

Shims for Ball Bearing Housings

Also called tolerance rings, these rings are for use in stamped, molded, or worn housings to form a tight hold on the bearings.

Slotted Shims

The slot lets you insert, remove, and adjust the shims without disassembling your machinery.

Slotted Shim Sets

Be prepared with slotted shims in a variety of thicknesses. The slot lets you insert, remove, and adjust the shims without disassembling your machinery.

Multi-Slotted Shims

Use a single shim on feet or positioning arms that are secured with multiple fasteners. The slots let you insert, remove, and adjust the shims without disassembling your machinery. Also known as finger shims.

Shim Stock

Cut this stock into custom shapes to fit your application.

Washer Assortments

Split Lock Washer Assortments

As a screw is tightened, these washers flatten to add tension to the joint and prevent loosening from small amounts of vibration.

Sleeve Bearings

Oil-Embedded Sleeve Bearings

Also known as Oilite® bearings.

High-Load Oil-Embedded
Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Vibration-Damping
Oil-Embedded Sleeve Bearings

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

Panel-Mount Oil-Embedded
Sleeve Bearings

Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels.

Light Duty Dry-Running
Sleeve Bearings

Use where high loads and speeds are not required.

High-Load Dry-Running
Sleeve Bearings

A metal shell adds strength.

High-Temperature
Dry-Running Sleeve Bearings

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

Ultra-Low-Friction
Dry-Running Sleeve Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Food Industry Dry-Running
Sleeve Bearings

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Chemical-Resistant
Dry-Running Sleeve Bearings

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Water-Resistant Dry-Running
Sleeve Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

High-Speed Panel-Mount
Dry-Running Sleeve Bearings

Made of acetal and PTFE plastic, these panel-mount bearings handle speeds twice as fast as standard acetal bearings can.

Panel-Mount Dry-Running
Sleeve Bearings

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.

Multipurpose Sleeve Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Multipurpose Sleeve
Bearings with Groove

A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface.

Corrosion-Resistant Sleeve Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Flanged Sleeve Bearings

Light Duty Dry-Running
Flanged Sleeve Bearings

Use where high loads and speeds are not required.

Food Industry Dry-Running
Flanged Sleeve Bearings

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

Ultra-Low-Friction Dry-Running
Flanged Sleeve Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Easy-Install Dry-Running
Flanged Sleeve Bearings

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

Chemical-Resistant Dry-Running
Flanged Sleeve Bearings

These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.

Multipurpose Dry-Running
Flanged Sleeve Bearings

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

High-Load Dry-Running
Flanged Sleeve Bearings

An aluminum shell adds strength.

Water-Resistant Dry-Running
Flanged Sleeve Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Self-Aligning Dry-Running
Flanged Sleeve Bearings

Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.

High-Speed Self-Aligning Dry-Running
Flanged Sleeve Bearings

Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.

Oil-Embedded Flanged
Sleeve Bearings

Also known as Oilite® bearings.

Multipurpose Flanged
Sleeve Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Corrosion-Resistant
Flanged Sleeve Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Thrust Bearings

Oil-Embedded Thrust Bearings

Also known as Oilite® bearings.

High-Load Oil-Embedded
Thrust Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Light Duty Dry-Running
Thrust Bearings

Use where high loads and speeds are not required.

High-Temperature
Dry-Running Thrust Bearings

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

Water-Resistant
Dry-Running Thrust Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Ultra-Low-Friction
Dry-Running Thrust Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

High-Load Dry-Running
Thrust Bearings

A metal backing adds strength.

Multipurpose Thrust Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Corrosion-Resistant Thrust Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Clamping and Workholding

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part.

Metric Press-Fit Drill
Bushings with Head

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit.

Screw-Mount Locating
and Support Buttons

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Press-Fit Locating
and Support Buttons

Support and position workpieces and fixtures from the bottom or side. These buttons press into a drilled hole for permanent installation.

Threaded Locating
and Support Buttons

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Shaft Collars

Clamping Shaft Collars

These metal collars are stronger than plastic shaft collars.

Washdown Clamping Shaft Collars

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Tight-Hold Quick-Release
Clamping Shaft Collars

A threaded lever lets you tighten these collars with more torque than other quick-release styles, ensuring that they stay put on your shaft.

Quick-Release Clamping Shaft Collars

Installing and removing a collar is as easy as pushing down and lifting up a clamp lever.

Extra-Wide Clamping Shaft Collars

Wider than standard shaft collars with twice the number of clamping screws, these ensure a better grip for greater holding power.

Set Screw Shaft Collars

Keep these shaft collars in place by tightening their set screw into the shaft.

Clamping Two-Piece Shaft Collars

These metal collars are stronger than plastic shaft collars.

Washdown Clamping
Two-Piece Shaft Collars

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Extra-Wide Clamping
Two-Piece Shaft Collars

Wider than standard shaft collars with twice the number of clamping screws, these ensure a better grip for greater holding power.

Quick-Release Two-Piece
Clamping Shaft Collars

Make quick adjustments to these shaft collars with a lever on the side.

Clamping Two-Piece Shaft
Collars with Wrench Flats

Use a wrench to rotate your drive shaft without marring or gouging the shaft.

Extra-Grip Clamping
Two-Piece Shaft Collars

With larger screws than those found on standard clamping collars, these provide a stronger grip on your shaft without using additional screws.

Inch-to-Metric Clamping
Two-Piece Shaft Collars

Although these collars fit inch-sized shafts, they have a metric OD and width for use with metric equipment.

Set Screw Two-Piece Shaft Collars

Tighten the set screw to bite into an unhardened shaft for a secure hold.

Hinged Shaft Collars

Offering the benefits of a two-piece collar in a one-piece design, these collars swing open for positioning then close anywhere on your shaft.

Mountable Shaft Collars

Flange-Mount Shaft Collars

Three tapped counterbored holes and three through-holes provide mounting flexibility.

Top-and-Bottom Mount
Two-Piece Shaft Collars

Secure items to either side of these collars—each half has a flat end with a tapped hole

Top-and-Bottom Mount Two-Piece
Quick-Release Clamping Shaft Collars

Mount items to either half of these collars and quickly adjust their position on shafts with a lever on the side. The two halves separate, so you can install them anywhere on a shaft without removing components or having access to the end.

Top-and-Bottom Mount Shaft Collars

Mount these collars flush against each other or attach components to either side—the round body has flattened ends with tapped holes.

Top-and-Bottom Mount
Quick-Release Clamping Shaft Collars

Attach items to tapped holes at either end of these collars and twist the lever to quickly move them along shafts.

Weldable Two-Piece Shaft Collars

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

Face-Mount Shaft Collars

Two tapped holes on the face of these collars allow you to fasten them to gears, pulleys, and sprockets.

Bearing Retaining Nuts

Bearing Retaining Locknuts

With a nylon insert that grips your threaded shaft or spindle without damaging the threads, these locknuts—sometimes called shaft nuts—keep bearings, bushings, gears, and pulleys in place.

Bearing Retaining Nuts

Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle.

Bearing Retaining Jam Nuts

Used in pairs or with another bearing retaining nut, these jam nuts—often called shaft nuts—hold bearings, bushings, pulleys, and gears in place on your threaded shaft or spindle.

Threaded Shaft Collars

To install, thread these one-piece collars onto the end of your shaft.

D-Profile Shaft Collars

To install, slide these one-piece collars onto the end of your shaft.

Bumpers

Threaded-Stud Bumpers

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

Load-Rated Threaded-Stud Bumpers

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

Heavy Duty Threaded-Stud Bumpers

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

High-Temperature Load-Rated
Threaded-Stud Bumpers

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

Threaded Bumpers

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

Load-Rated Threaded Bumpers

High-Temperature Load-Rated
Threaded Bumpers

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

Crane Bumpers

Designed to withstand repeated heavy hits on bridge or ceiling cranes, these bumpers protect walls or beams as well as extend crane life.

Shaft Grommets

Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.

Linear Bearings

Linear Ball Bearings

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

High-Temperature
Linear Ball Bearings

The choice for low-friction motion in high-temperature environments.

Linear and Rotary Ball Bearings

Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts.

High-Load Linear Ball Bearings

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings.

Dust-Resistant Linear
Sleeve Bearings

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Linear Sleeve Bearings

Because they usually do not require lubrication, linear sleeve bearings outperform linear ball bearings in dirty environments.

Food Industry Linear Sleeve Bearings

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance.

Linear Ball Bearings
for Support Rail Shafts

Ball bearings create less friction than sleeve bearings, so they require less force to operate.

High-Load Linear Ball Bearings
for Support Rail Shafts

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rail shafts.

High-Temperature Linear Ball
Bearings for Support Rail Shafts

The choice for low-friction motion in high-temperature environments.

Disc Springs

Belleville Disc Springs

Use these steel springs in noncorrosive environments.

Belleville Disc Springs
for Ball Bearings

Install these springs, also known as bearing preload washers, against ball bearings to reduce noise and unwanted movement along the shaft.

Split Wave Disc Springs

A gap allows these springs to compress without widening, so they won't bind or deform when used inside a housing with tight clearance.

Metric Clamping Acme Lead Screw Collars

Metric Clamping Acme
Lead Screw Collars

Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.

Stops and Spacers for DIN Rails

Position terminal blocks, relays, and other components mounted to DIN rails with these stops and spacers.

Ball Joint Rod End Inserts

Without changing the ID, these inserts handle some misalignment on rod ends.

Terms and Conditions and Privacy Policy

Spacers and Standoffs

Aluminum Unthreaded Spacers

18-8 Stainless SteelUnthreaded Spacers

Zinc-Plated BrassUnthreaded Spacers

Nylon Unthreaded Spacers

Male-Female Threaded Hex Standoffs

Female Threaded Hex Standoffs

Sanitary Threaded Standoffs

Press-Fit ThreadedStandoffs with Closed End

Press-Fit ThreadedStandoffs with Open End

Miniature Press-Fit ThreadedStandoffs with Open End

Vibration-Damping Snap-In Supports

Washers

Metric Oversized Washers

Metric General Purpose Washers

Metric Washers forStructural Applications

Metric Plastic Washers

Metric Chemical-ResistantPlastic Washers

Metric Electrical-InsulatingPlastic Washers

Metric Water- andSteam-Resistant Plastic Washers

Metric High-TemperaturePlastic Washers

Metric Extreme-TemperatureCeramic Washers

Square Washers

Metric Countersunk Washers

Plastic Countersunk Washers

Metric FinishingCountersunk Washers

Sleeve Washers for Soft Material

Self-Retaining Washers

Clipped Washers

Oversized Clipped Washers

Lock Washers

Metric Split Lock Washers

Metric Split Lock Washersfor Socket Head Screws

Metric External-Tooth Lock Washers

Tight-Grip External-ToothLock Washers

Metric Internal-Tooth Lock Washers

Internal-/External-ToothLock Washers

Metric Spring Lock Washers

Spring Lock Washersfor Slotted Bearing Nuts

Belleville Spring Lock Washersfor Socket Head Screws

Spring Lock Washersfor Plastic Screws

Wedge Lock Washers

Metric Tab Lock Washers

Abrasion-Resistant Leather Washers

Abrasion-Resistant Leather Washers

Sealing Washers

Pressure-Rated Metal-BondedSealing Washers

Metric High-Pressure-RatedMetal-Bonded Sealing Washers

Metal Sealing Washers

Leveling and Wave Washers

Metric Leveling Washers

Triple-Wave Washers

Metric Single-Wave Washers

Metric Leveling Washers for I-Beams

Thread Adapters

Metric-to-Metric Male-FemaleHex Thread Adapters

Inch-to-Metric Male-FemaleHex Thread Adapters

Male-Female Round UniversalThread Adapters with Through Hole

Metric-to-Metric MaleHex Thread Adapters

Metric-to-Metric MaleRound Thread Adapters

Inch-to-Metric MaleHex Thread Adapters

Inch-to-Metric MaleRound Thread Adapters

Male Round Universal ThreadAdapters with Through Hole

Shims

Ring Shims

Shims for ShorteningScrew Shoulders

Shims for LengtheningScrew Shoulders

Shims for Ball Bearing Housings

Slotted Shims

Slotted Shim Sets

Multi-Slotted Shims

Shim Stock

Washer Assortments

Washer Assortments

Split Lock Washer Assortments

Sleeve Bearings

Oil-Embedded Sleeve Bearings

High-Load Oil-EmbeddedSleeve Bearings

Vibration-DampingOil-Embedded Sleeve Bearings

Panel-Mount Oil-EmbeddedSleeve Bearings

18-8 Stainless Steel
Unthreaded Spacers

Zinc-Plated Brass
Unthreaded Spacers

Press-Fit Threaded
Standoffs with Closed End

Press-Fit Threaded
Standoffs with Open End

Miniature Press-Fit Threaded
Standoffs with Open End

Metric Washers for
Structural Applications

Metric Chemical-Resistant
Plastic Washers

Metric Electrical-Insulating
Plastic Washers

Metric Water- and
Steam-Resistant Plastic Washers

Metric High-Temperature
Plastic Washers

Metric Extreme-Temperature
Ceramic Washers

Metric Finishing
Countersunk Washers

Metric Split Lock Washers
for Socket Head Screws

Tight-Grip External-Tooth
Lock Washers

Internal-/External-Tooth
Lock Washers

Spring Lock Washers
for Slotted Bearing Nuts

Belleville Spring Lock Washers
for Socket Head Screws

Spring Lock Washers
for Plastic Screws

Pressure-Rated Metal-Bonded
Sealing Washers

Metric High-Pressure-Rated
Metal-Bonded Sealing Washers

Metric-to-Metric Male-Female
Hex Thread Adapters

Inch-to-Metric Male-Female
Hex Thread Adapters

Male-Female Round Universal
Thread Adapters with Through Hole

Metric-to-Metric Male
Hex Thread Adapters

Metric-to-Metric Male
Round Thread Adapters

Inch-to-Metric Male
Hex Thread Adapters

Inch-to-Metric Male
Round Thread Adapters

Male Round Universal Thread
Adapters with Through Hole

Shims for Shortening
Screw Shoulders

Shims for Lengthening
Screw Shoulders

High-Load Oil-Embedded
Sleeve Bearings

Vibration-Damping
Oil-Embedded Sleeve Bearings

Panel-Mount Oil-Embedded
Sleeve Bearings

Light Duty Dry-Running
Sleeve Bearings

High-Load Dry-Running
Sleeve Bearings

High-Temperature
Dry-Running Sleeve Bearings

Ultra-Low-Friction
Dry-Running Sleeve Bearings

Food Industry Dry-Running
Sleeve Bearings

Chemical-Resistant
Dry-Running Sleeve Bearings

Water-Resistant Dry-Running
Sleeve Bearings

High-Speed Panel-Mount
Dry-Running Sleeve Bearings

Panel-Mount Dry-Running
Sleeve Bearings

Multipurpose Sleeve
Bearings with Groove

Light Duty Dry-Running
Flanged Sleeve Bearings

Food Industry Dry-Running
Flanged Sleeve Bearings

Ultra-Low-Friction Dry-Running
Flanged Sleeve Bearings

Easy-Install Dry-Running
Flanged Sleeve Bearings

Chemical-Resistant Dry-Running
Flanged Sleeve Bearings

Multipurpose Dry-Running
Flanged Sleeve Bearings

High-Load Dry-Running
Flanged Sleeve Bearings

Water-Resistant Dry-Running
Flanged Sleeve Bearings

Self-Aligning Dry-Running
Flanged Sleeve Bearings

High-Speed Self-Aligning Dry-Running
Flanged Sleeve Bearings

Oil-Embedded Flanged
Sleeve Bearings

Multipurpose Flanged
Sleeve Bearings

Corrosion-Resistant
Flanged Sleeve Bearings

High-Load Oil-Embedded
Thrust Bearings

Light Duty Dry-Running
Thrust Bearings

High-Temperature
Dry-Running Thrust Bearings

Water-Resistant
Dry-Running Thrust Bearings

Ultra-Low-Friction
Dry-Running Thrust Bearings

High-Load Dry-Running
Thrust Bearings

Metric Press-Fit Drill
Bushings with Head

Screw-Mount Locating
and Support Buttons

Press-Fit Locating
and Support Buttons

Threaded Locating
and Support Buttons

Tight-Hold Quick-Release
Clamping Shaft Collars

Washdown Clamping
Two-Piece Shaft Collars

Extra-Wide Clamping
Two-Piece Shaft Collars

Quick-Release Two-Piece
Clamping Shaft Collars

Clamping Two-Piece Shaft
Collars with Wrench Flats

Extra-Grip Clamping
Two-Piece Shaft Collars

Inch-to-Metric Clamping
Two-Piece Shaft Collars

Top-and-Bottom Mount
Two-Piece Shaft Collars

Top-and-Bottom Mount Two-Piece
Quick-Release Clamping Shaft Collars

Top-and-Bottom Mount
Quick-Release Clamping Shaft Collars