More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

Made from 18-8 stainless steel, these screws have good chemical resistance. A flange under the head distributes pressure over the surface, eliminating the need for a washer.

Made from 18-8 stainless steel, these screws have good chemical resistance. Their flange is serrated to help prevent loosening from vibration.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

Often used to fasten parts in engines and turbines, these are our strongest stainless steel screws. They are comparable in strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water. Use these low-profile screws where space is limited.

The nylon patch bonded to the threads of these socket head screws adds friction to keep vibration from loosening them, while their O-ring prevents leaks and seals out contaminants.

Seal out contaminants and prevent leaks—a rubber O-ring under the head prevents leaks and seals out contaminants.

Closely spaced threads on these screws fit in holes with a fine pitch. They're not compatible with standard metric threads.

Made from 18-8 stainless steel, these metric pan head screws have good chemical resistance and may be mildly magnetic.

Made to Japanese Industrial Standards, these screws have narrower and shorter heads than standard Phillips pan head screws.

These metric 316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. The extra-wide truss head distributes holding pressure to reduce the likelihood of crushing thin material. Screws may be mildly magnetic.

More corrosion resistant than steel, and almost as strong, these 18-8 stainless steel screws have a narrower head than pan head screws to fit into tight spaces. They’re often used in electrical panels and next to flanges and raised surfaces in humid, damp, and washdown environments, but will corrode if exposed to salt water or chemicals.

Good for use outdoors and in washdown environments, these metric 18-8 stainless steel screws are more corrosion resistant than steel and nearly as strong. Their pan-shaped head sits nearly flat on the fastened surface, so there’s no need to countersink a hole.

Fit these metric screws into spaces where head height is important and other wide head screws won't fit. Also known as shutter screws, they have an ultra-wide truss head to distribute the load over a large area for excellent holding pressure.

18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. A Torx drive has more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

These metric 316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer. Screws may be mildly magnetic.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. The flange is wider and thicker than our other flanged screws, so they distribute pressure the best.

Made from 18-8 stainless steel, these metric button head screws have good chemical resistance and may be mildly magnetic. The tamper-resistant Torx drive (also known as a pin-in Torx drive) makes them difficult to remove without special tools.

These metric screws have a drilled spanner drive, making them difficult to remove without special tools. Made from 18-8 stainless steel, they have good chemical resistance and may be mildly magnetic.

These metric screws have a nylon patch bonded to the threads that adds friction to prevent loosening from vibration. Made from 18-8 stainless steel, they have good chemical resistance and may be mildly magnetic.

These metric stainless steel screws have good chemical resistance and may be mildly magnetic. All have a washer with sharp external teeth that dig into surfaces for maximum holding power and vibration resistance. Also known as Sems screws, the washer rotates freely but is permanently attached.

Closely spaced threads on these screws fit in holes with a fine pitch. They're not compatible with standard metric threads.

These metric screws have good chemical resistance and may be mildly magnetic.

These screws meet Japanese Industrial Standards.

These metric A286 stainless steel screws have comparable strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

More corrosion resistant than 18-8 stainless steel screws, these metric screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

To prevent leaks and seal out contaminants, these metric screws have an O-ring under the head.

With an O-ring under the head, these metric screws seal out leaks and contaminants while also preventing unwanted removal.

With a tamper-resistant hex drive (also known as a pin-in hex drive), these metric screws are difficult to remove without special tools.

To vent fluids and gases trapped under the screw, these metric screws are drilled through the shaft.

With inch-sized threads the same diameter as the shoulder, these screws can handle heavy loads. They’re 18-8 stainless steel for good chemical resistance.

With a shoulder that’s twice as precise as standard shoulder screws, these metric shoulder screws act as a shaft or axle for bearings and other moving parts in applications that require smooth and accurate movement, such as measuring and lab equipment. Made of 18-8 stainless steel, they’re nearly as strong as steel but won’t rust in outdoor or washdown environments.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a thin, knurled head for use in low-clearance applications.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a raised head that makes them easy to grip.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

More corrosion resistant than 18-8 stainless steel bolts, these bolts have excellent resistance to chemicals and salt water. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

These metric set screws have good chemical resistance.

Made from 18-8 stainless steel, these metric set screws are chemical resistant. They have a nylon locking patch that grips threads to resist loosening.

Also known as dog-point set screws, these metric set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned. Made of 18-8 stainless steel, they have good chemical resistance.

These metric 316 stainless steel set screws have excellent chemical resistance and can be used in saltwater environments. The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

Available in metric sizes, these screws have a tip that is harder than nylon and silver to provide a secure hold on hard surfaces. The body is 18-8 stainless steel for good chemical resistance.

These metric 18-8 stainless steel set screws are chemical resistant. A pointed tip wedges into the contact surface for a secure hold on soft materials such as brass.

Install these thumb-screw-head screws through a hole and thread on a retainer to keep secure—no special tools are required.

18-8 stainless steel screws have good chemical resistance.

Use these hex drive screws and binding barrels as a low-profile alternative to standard nut and bolt combinations.

Flat head screws are angled under the head to fit flush within countersunk holes.

Set screws exert pressure at the tip to hold objects in place.

18-8 stainless steel studs have good chemical resistance.

Also known as nut eyebolts, these are designed for through-hole applications.

Create your own lifting eye by adding an eye nut to a stud or bolt.