Over 48,000 metals now include traceable material certificates.

Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.

18-8 stainless steel spacers have good corrosion resistance.

These spacers have excellent wear and abrasion resistance. Exposure to moisture may cause them to expand.

These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Twist these adapters onto female metric threads to change pitch or switch thread sizes.

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

These metric coupling nuts have good chemical resistance.

For light duty applications, choose these metric-sized coupling nuts.

These metric-sized coupling nuts are Class 10 steel, so they’re about 25% stronger than medium-strength steel coupling nuts.

Stainless steel coupling nuts have excellent corrosion resistance in most environments.

Use where high loads and speeds are not required.

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

A metal shell adds strength.

Good for underwater applications, these bearings won’t swell or warp when wet.

Also known as Oilite® bearings.

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

Embedded with oil that is safe for incidental contact with food, these bearings are suitable for use in high-load applications such as bottling and filling lines in food processing plants. They are also known as Super Oilite® bearings.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Use where high loads and speeds are not required.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

An aluminum shell adds strength.

Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

Good for underwater applications, these bearings won’t swell or warp when wet.

Also known as Oilite® bearings.

The oil in these bearings is suitable for incidental contact with food.

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part.

Use these brackets for extra mounting space behind DIN rail to accommodate wiring and bulky items.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

With two bearings mounted in one housing, these sleeve bearings can handle heavier loads than standard mounted linear sleeve bearings.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

With two bearings mounted in a single housing, these bearings have higher load capacities than standard ones. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.