These metric Grade B7 fine-threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.

These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

Fiberglass threaded rods are stronger than nylon threaded rods. They resist acids, solvents, salt water, and oil.

18-8 stainless steel studs have good chemical resistance.

These steel studs are zinc plated to resist corrosion in wet environments.

Pass these studs through a hole and weld them in place.

Install these thumb-screw-head screws through a hole and thread on a retainer to keep secure—no special tools are required.

Lock the nose into the retracted position by pulling the knob and rotating it 90°.

Lock the nose into the retracted position by pulling the handle and rotating it 90°.

These spring plungers have a nose that is about three-times longer than standard long hex-nose spring plungers.

Slotted on both ends for installation with a screwdriver.

Also known as tap-end and fixture studs, these rods have friction-fit threads on one end to resist loosening and standard threads on the other side for attaching a nut.

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

The shoulder on these tooling balls provides a consistent height reference point.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

As the workpiece pushes against the pin head in one direction, the internal spring pushes back to hold it in place for clamping.

Get everything needed for basic workholding on a machine table.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

An oil-embedded bronze insert slowly releases lubricant to the rod end. Connect your grease gun to the fitting to relubricate.

Made of impact-resistant nylon, these externally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

Pivot and hinge components in wet and corrosive environments with these stainless steel or brass rod end bolts.

These black-oxide steel rod end bolts are heat treated for added strength.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

These metric lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects. They're commonly found in hand-powered clamps, vises, grates, doors, and work tables.

Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.

Install these nuts on a rotary shaft to create a linear positioning system without a lead screw. Instead of threads, a set of angled ball bearings drives the nut along a shaft as it spins.