Good for occasional machining, economy kits contain lower-strength components than standard kits.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.

The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.

Use these blocks to support setup clamps. Fit the nonslip steps together for quick height adjustments.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Screw these clamps directly into a tapped hole in a fixture.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Hold workpieces of different thicknesses without adjustment.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

The mounting base secures these clamps to a rail or bar.

Mount these clamps below a surface.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

These clamps have twice the capacity of standard C-clamps.

These clamps are made of stainless steel for excellent corrosion resistance.

Lighter weight than other metal clamps, these are less likely to bend thin material.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

Three screws apply pressure to three sides of a workpiece.

With no handle or protruding screw, these clamps can fit into tight spaces.

Apply pressure to the side of a workpiece as well as the top and bottom.

Plastic clamping surfaces prevent damage to material.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Hold workpieces of different thicknesses without adjustment.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

The plunger can be locked at any position along its travel.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.