Also known as tactile switches, these are small enough to fit inside a computer keyboard.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

More durable than standard metal switches, these can handle tough, repetitive use.

The face of these switches mounts flush against a panel, so they're easy to clean and hard to damage.

Save space on a panel by using one switch to perform multiple switching functions.

Install in 12 mm dia. cutouts.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

These switches are housed in a durable steel enclosure.

With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.

A rubber seal protects these switches from washdowns.

Maximize the space in a panel—these switches are half the size of most toggle switches.

Built into a terminal block, these switches mount to DIN rail.

Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.

With a durable steel housing, these switches withstand tough, repetitive use.

Choose an actuator and contact block to make your own 30 mm switch.

Choose an actuator and contact block to make your own 16 mm switch.

Use these hand-held switches with mobile machinery.

With a slim shape, these switches fit comfortably in your hand.

A durable rubber housing covers the buttons and protects these switches from impact.

Install in 16 mm dia. cutouts.

Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.

Use this switch for intermittent, light-duty applications.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Customize the length of these switches by cutting them from a 50-foot roll.

Customize the length of these switches by cutting them from a 25-foot roll.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Smaller than standard size snap-acting switches, these fit in tight spaces.

Actuate these switches with half the force of other subminiature switches for increased accuracy.

With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from washdowns and temporary submersion.

Rated NEMA 4 , these enclosed switches have a sealed actuator for protection from washdowns.

Sealed actuators prevent these switches from jamming, even when exposed to oil, sand, mud, or ice.

Stack these slim switches together, or fit them into tight spaces. They're rated IP67 for protection from temporary submersion.

These switches actuate with the slightest push for a high degree of accuracy. They're rated IP67 for protection from washdowns and temporary submersion.

Rated IP67, these switches are protected from temporary submersion.

Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.

Use these switches where ignitable gas and dust may be present. They meet UL Class I, Divisions 1 and 2, Groups B, C, and D; and Class II, Divisions 1 and 2, Groups E, F, and G for hazardous locations.

Minimize false triggers—these switches require 10 lbs. of actuation force in order to shut off machinery immediately.

Combine a foot-pedal actuator with a switching mechanism to build a complete switch.

Combine a push-button actuator with a switching mechanism to build a complete switch.

Attach quick-disconnect terminals or plug relays into relay sockets.

Smaller than standard spade-terminal relays in height and depth, these relays save space inside your control cabinet.

Thinner than other spade-terminal relays, these fit in tight spaces.

Use the screw terminals to hardwire these relays.

These sealed relays meet UL Class I, Division 2, Groups A, B, C, and D for use in hazardous locations.

More durable than standard relays, use these relays with motors and pumps.

The interlocked opposing contacts won't close at the same time, so these relays are suitable for safety applications such as machine guarding.