The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Use these pumps to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers

Use less electricity to achieve the same flow rates as other circulation pumps.

Also known as turbine pumps, these have a specialized impeller that propels water about four times higher and farther than standard circulation pumps. They're commonly used with chillers, heat exchangers, and boiler feed systems.

Eliminate seal wear and leakage with pumps that use magnets to turn the impeller. They’re often used with electroplating and photographic solutions.

A powerful motor provides twice the flow rate of other extended-life circulation pumps. The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Magnets turn the impeller to eliminate seal wear and leakage for a long service life. These pumps are often used with electroplating and photographic solutions.

These pumps have high flow rates for irrigation and landscaping.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Install these pumps up to 20 ft. above your liquid source to drain underground tanks and process wastewater.

Eliminate seal wear and leakage—these pumps have magnets that turn the impeller for a long service life. Install them directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

A detachable motor assembly allows you to leave these pumps inline while servicing or repairing the motor. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Use these pumps in pipelines with limited clearance. Install directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Commonly used in machine tool coolant tanks, these pumps have an intake that can be completely submerged in liquid.

The durable motor and impeller can handle dirty coolant and machine lubricants with solids up to 1/4" diameter. These pumps have an intake that can be completely submerged in liquid.

A 316 stainless steel housing sealed with fluoroelastomer resists mild chemicals and acids, such as coolant, oil, and phosphoric acid.

A Noryl housing and impeller with a fluoroelastomer seal provide good resistance to acids, alkalies, and inorganic solvents. These pumps are often used for circulating mild caustics such as salt water and antifreeze

Keep your circulation pump in working order by replacing broken or worn parts.

Also known as gear pumps, these produce a smooth flow of liquid for applications such as cooling engines, powering hydraulic equipment, and extracting liquid from holding tanks.

An aluminum enclosure around the motor provides protection in dusty and dirty environments. Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

A cast iron housing and steel gears allow these pumps to be used with hydraulic and motor lubricating oil. Also known as gear pumps, they produce a smooth flow of liquid for applications such as engine lubrication.

These pumps have a bronze housing and brass or bronze gears for use with water. Also known as gear pumps, they produce a smooth flow of liquid for water delivery.

Also known as plunger pumps, these can provide pressures up to 3,600 psi. Use them for washdowns, drain jetting, and other pressurized water-spraying applications.

Also known as flexible impeller pumps, these create a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

Pumps have a powerful motor that provides more than twice the flow rate of standard water-removal pumps to quickly remove large volumes of liquid. They activate when plugged in; add a plug-in switch to control when the pump activates.

These pumps have a powerful motor that provides more than twice the flow rate of standard water-removal pumps to quickly remove large volumes of liquid.The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Use the handle to carry this pump from job to job. A float switch is wired to the pump.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

Transfer raw sewage water that contains solids up to 2” in diameter. These pumps have a float switch with a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

The float switch has a separate cord that can unplug, so you can repair the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

The intake is 2" from the base of the pump to prevent dirt at the bottom of your sump pit from clogging the pump. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

The float switch is wired to the pump. Use with debris-free water.

Pumps have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Use with debris-free water.

These unthreaded rubber strainers fit onto 3/4 NPT male connections.

An alarm and a red light alert you when water levels rise too high.

These pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Use them to transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Equipped with a large intake and a rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. Pumps transfer raw sewage water with solids up to 2” in diameter.

Activate your pump in dirty water that contains sludge and sewage. These switches have no moving parts for a longer life than float switches.

If the primary float fails, the backup float kicks in and an alarm sounds to indicate float malfunction.

Install these pumps in a panel cutout. Often used in food and beverage, pharmaceutical, and lab applications, they dispense small amounts of liquid at a set rate.

An adjustment dial with a locking lever allows for easy flow control. Also known as diaphragm metering pumps, these can be used with pressures up to four times higher than standard pumps for chemicals.

For high-volume chemical sampling and draining, these pumps have a powerful motor that enables them to move 2,448 gallons of liquid per day.

Rated for liquids with a viscosity up to 10,000 centipoise, these pumps can be used with very thick chemicals such as electropolishing solutions.

These pumps can be used with pressures four times higher than standard pumps for chemicals.

An adjustment screw lets you increase or decrease flow rate without the hassle of changing tubing. Often used in boiler feed systems and water treatment, these pumps are compatible with chemicals such as cleaning fluids and acid-washing solutions.

Keep your metering pump in working order by replacing worn parts.

Drain and transfer liquid more quickly and easily than hand-operated pumps and siphon pumps.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

Including nozzles and connectors, these pumps come with everything you need to start pumping.

These pumps are rated for fuel such as gasoline, kerosene, and diesel fuel.

Achieve powerful vacuum and continuous flow for applications such as vacuum drying, solvent evaporation, and distillation.

Use these pumps in applications such as degassing and servicing refrigeration and freezer systems.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard steam condensate pumps. Use in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard high-flow steam condensate pumps. These pumps move a higher volume of condensate than standard steam condensate pumps. Use them in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

Designed for use in low-pressure steam systems, these pumps capture steam in the attached tank and return hot condensate to your boiler or feed unit.

The stainless steel tank has excellent corrosion resistance. Designed for use in low-pressure steam systems, these pumps capture steam in the attached tank and return hot condensate to your boiler or feed unit.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Magnets turn the impeller so there's no shaft seal to wear out. Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Create and supply hydraulic pressure. Units include a fixed-displacement gear pump, AC motor, tank, and breather vent.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

These dispensers have a reservoir for recirculating coolant.