Zinc-plated steel is more corrosion resistant than nickel-plated steel.

Black-oxide steel has a dull shine for areas where appearance is a concern.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

An offset mounting hole allows for installation without moving your machine.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Nickel-plated steel has some corrosion resistance.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Use these mounts on heavy machines and equipment.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Protect surfaces from scratches and wear.

Meant for light duty applications, these mounts are not rated for capacity.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

These mounts have a cushion on top to provide padding between your furniture and the mount.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Higher deflection ratings translate to greater vibration and shock isolation.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

Higher deflection ratings translate to greater vibration and shock isolation.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

Limit damage during moderate earthquakes.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

Well-suited to moist environments, these mounts have a stainless steel plate for excellent corrosion resistance.

Made of neoprene rubber, these mounts are oil resistant, so they're good for use under generators, HVAC equipment, electric motors, pumps, and blowers.

A two-piece design makes these mounts easier to install than one-piece mounts.

Install these mounts with a socket head cap screw—the counterbored hole ensures the screw sits flush with or below the top of the mount.

Specifically designed for light vertical loads, these mounts buckle to protect lightweight equipment such as small fans and pumps from vibration.

Isolate vibration and noise from oscillating equipment like fans and tumblers that create horizontal (shear) force.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

Ribbed grommets are more flexible than our smooth vibration-damping grommets, so they're easier to install.

In addition to having a wider temperature range than our other vibration-damping grommets, these have excellent weather resistance.

In addition to having a wider temperature range than our other vibration-damping bushings, these have excellent weather resistance.

Use these in place of normal washers to damp vibration and cushion your joint.

These feet are made of UHMW polyethylene plastic, so they won’t dry out and become brittle.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

Make bumpers the size and shape you need. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.