McMaster-Carr logo
    Filter by
    Shaft Diameter
    Body Shape
    Overall Width
    Shaft Length
    Number of Shafts
    Overall Height
    Direction of Operation
    Full Step Increment
    Wire Lead Color
    Number of Wire Leads
    Thrust Load Capacity
    Motor Type
    Shaft Type
    Face Shape
    Enclosure Material
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    DFARS Specialty Metals
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    8 Products

    Stepper Motors

    Motors
    Image of Product. Square Body. Front orientation. Stepper Motors. Motors, Square Body.

    Square Body

    Image of Attribute. Front orientation. Contains Annotated. Motors.
    Image of Attribute. Side1 orientation. Contains Annotated. Motors.
    These stepper motors are good for precise, repetitive movements, such as those made by the head of a 3D printer. Similar to the hands of a clock, their shaft turns in small, equal increments. When the shaft stops, it holds its position even when a counteracting force is applied to the load. You can control the position of the load without having to configure encoders or sensors. All are bipolar hybrid stepper motors, so the current can flow in both directions. This helps them deliver higher torque, precision, and efficiency than unipolar stepper motors.
    All motors require a controller and drive (not included).
    Maximum Holding Torque—Holding torque is the force needed to move the shaft out of position when it is stationary. When the shaft is in motion, torque generally decreases as speed increases. Use a torque-speed curve to confirm which motor will work for your application. Click on a part number and select “Product Detail” to view the curve for a motor.
    Full Step Increment—Full step increment is the rotation of the shaft from one position to the next. A smaller full step increment means the rotor has more teeth, producing smoother and more precise motion. 1.8° is considered standard.
    Overall
    Shaft
    Temp.
    Range, ° F
    Max. Holding
    Torque, in·ozf
    Max. Rotation
    Speed, rpm
    Max. Current
    per Phase, amp
    Full Step
    Increment
    Stepper Motor
    Polarity
    No. of Wire
    Leads
    Lg.
    Wd.
    Ht.
    Dia.,
    mm
    Lg.,
    mm
    Ctr.-to-Base
    Lg.
    Type
    No. of
    Shafts
    Min.
    Max.
    Each
    Square Body
     
    NEMA 11 Frame Size
    8.53,3000.671.8°Bipolar42.1"1.1"1.1"5180.56"Solid1012000000000000000
    142,4750.671.8°Bipolar42.6"1.1"1.1"5180.56"Solid101200000000000000
    172,4750.671.8°Bipolar42.8"1.1"1.1"5180.56"Solid101200000000000000
     

    Stepper Servomotors with Integrated Drive

    Image of Product. Front orientation. Servomotors. Stepper Servomotors with Integrated Drive.
    Simplify your servomotor setup—these servomotors have a built-in drive, removing the need for cable between the motor and drive. They create high torque at low speeds like traditional stepper motors but with greater torque performance and positioning reliability.
    These servomotors accept step and direction, position, speed, torque, or sequencing commands. Use a computer to set up and calibrate the motor to your system. After initial setup, use a separate controller, such as a programmable logic controller (PLC), microcontroller, or indexer. You can also store target positions with speeds and accelerations in the drive and then trigger each sequence with minimal input from a controller. The encoder relays distance, direction, and speed back to the servomotor. Based on this feedback, the servomotor dynamically adapts its movements to increase system efficiency.
    Maximum Holding Torque—Holding torque is the force needed to move the shaft out of position when it is stationary. Torque generally decreases as speed increases. Use a torque-speed curve to confirm which motor will work for your application. Click on a part number and select "Product Detail" to view the curve for a motor.
    Overall
    Shaft
    No. of
    Inputs/Outputs
    Max. Holding
    Torque, in·ozf
    Max. Rotation
    Speed, rpm
    Voltage,
    V DC
    Current,
    amp
    Step
    Resolution
    Full Step
    Increment
    Lg.
    Wd.
    Ht.
    Dia.,
    mm
    Lg.,
    mm
    Ctr.-to-Base
    Lg.
    Communication
    Protocol
    Digital
    Inputs
    Digital
    Outputs
    Enclosure
    Rating
    Each
    NEMA 11 Frame Size
    9.23,00015 to 300.91 to 1/2561.8°2.7"1.1"1.5"5130.57"Modbus RTU42IP20
    		00000000000000
    11.33,00015 to 3011 to 1/2561.8°3"1.1"1.5"5130.57"Modbus RTU42IP20
    		0000000000000
    17.73,00015 to 3011 to 1/2561.8°3.5"1.1"1.5"5130.57"Modbus RTU42IP20
    		0000000000000
     

    Clean Room Stepper Motors

    Deliver precise, repeatable motion in applications where contamination is a concern, such as semiconductor manufacturing. These motors meet the strictest clean room standards—all components are cleaned and assembled in a clean room and stored in vacuum sealed packaging. Made of treated aluminum, they minimize gas and particle emission in your clean room’s environment. They're often used in vacuum chambers, where low particle emission prevents the vacuum from degrading. Similar to the hands of a clock, the shaft on these stepper motors turns in small, equal increments for smooth motion. When the shaft stops, it holds its position even when a counteracting force is applied to the load. You can control the position of the load without having to configure encoders, sensors, or other position feedback devices. All are bipolar hybrid stepper motors, so the current can flow in both directions. This helps them deliver higher torque, precision, and efficiency than unipolar stepper motors.
    All motors require a controller and drive (not included).
    Motors
    Image of Product. Front orientation. Stepper Motors. Clean Room Stepper Motors.
    Image of Attribute. Front orientation. Contains Annotated. Clean Room Stepper Motors, Motors.
    Image of Attribute. Side1 orientation. Contains Annotated. Clean Room Stepper Motors, Motors.
    Maximum Holding Torque—Holding torque is the force needed to move the shaft out of position when it is stationary. When the shaft is in motion, torque generally decreases as speed increases. Use a torque-speed curve to confirm which motor will work for your application. Click on a part number and select “Product Detail” to view the curve for a motor.
    Full Step Increment—Full step increment is the rotation of the shaft from one position to the next. A smaller full step increment means the rotor has more teeth, producing smoother and more precise motion. 1.8° is considered standard.
    Overall
    Shaft
    Temp.
    Range, ° F
    Max. Holding
    Torque, in·ozf
    Max. Rotation
    Speed, rpm
    Max. Current
    per Phase, amp
    Full Step
    Increment
    Stepper Motor
    Polarity
    No. of Wire
    Leads
    Lg.
    Wd.
    Ht.
    Dia.,
    mm
    Lg.,
    mm
    Type
    No. of
    Shafts
    Vacuum Rating,
    Torr
    Min.
    Max.
    Clean Room
    Std.
    Each
    Square Body
     
    NEMA 11 Frame Size
    103,2500.671.8°Bipolar42.1"1.1"1.1"518Solid11× 10^-70120ISO Class 1
    		0000000000000000
    19.51,5500.671.8°Bipolar42.8"1.1"1.1"518Solid11× 10^-70120ISO Class 1
    		000000000000000
     
    back to top