Zinc-plated steel is more corrosion resistant than nickel-plated steel.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Broader, stronger threads enable faster adjustments and higher load capacities than standard V-shaped threads.

Punch-out holes in the base let you bolt down these metric mounts to keep your equipment stationary.

Well-suited to damp environments, these metric mounts have a stainless steel stud and nut for corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Nickel-plated steel has some corrosion resistance.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.

Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.

Use these metric mounts on heavy machines and equipment.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

A hex nut at the base of the stud allows for easy height adjustment.

Meant for light duty applications, these mounts are not rated for capacity.

Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

Bolt these mounts down to keep your equipment stationary.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of nitrile rubber, these mounts are oil resistant for use in compression load applications with punch presses, milling machines, grinders, and air compressors.

Install these mounts with a socket head cap screw—the counterbored hole ensures the screw sits flush with or below the top of the mount.

A two-piece design makes these mounts easier to install than one-piece mounts.

Designed for tight spaces such as inside machinery, these mounts fit into a cutout, so they so they have a low top profile.

An integral cushion reduces noise and vibration.

A swiveling base compensates for angled legs and uneven surfaces.

A swiveling base compensates for angled legs and uneven surfaces.

Place these feet under furniture and equipment.

Cover the bottom of furniture legs.

These feet are made of UHMW polyethylene plastic, so they won’t dry out and become brittle.

Rated for high load capacity, use these metric inserts to connect threaded leveling mounts to heavy equipment.

Insert these adjustable mounts into tube ends to level your equipment in a single step.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

A magnetic base makes it easy to attach, move, and replace these bumpers on metal surfaces. Use them for guarding, aligning, and positioning parts.

These locks bolt or weld to the side of equipment that can't accommodate a floor lock underneath. Compatible with a wide range of caster mount heights.

Use screws or bolts to attach the mounting plate on these casters to a flat surface. Adjust the leveling pad to keep your equipment stationary and compensate for uneven floors.

The dual-wheel design provides better load distribution and easier turning than leveling plate casters. Adjust the leveling pad to keep your equipment stationary and compensate for uneven floors.

Made of 100% wool, this is the hardest felt we offer, yet it can still be used for polishing. It is more abrasion resistant and better at damping vibration than other felt. Includes S2-32, S2-24, and S2-20 felt grades.

This synthetic felt is an economical alternative to wool felt.