Use brackets and connectors to create vertical and horizontal support arms.

These rods have a bracket on the base so they're ready to mount.

The pivoting joint on these rods makes angle-mounting easy.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Replace worn shafts in two-piece support-rail shaft systems, or mate with a support rail to create your own. The tapped mounting holes match those on our Support Rails.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

These shafts have keyways only on the ends, leaving a plain shaft in the center. Use the keyways with machine keys to transmit torque to gears, sprockets, and other keyed components. Use the middle of the shaft with bearings and other round-bore components.

Stronger and more wear resistant than 18-8 stainless steel, these threaded rods are mildly chemical resistant. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

18-8 stainless steel threaded rods have good chemical resistance.

Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

The most corrosion resistant stainless steel threaded rods we offer, these Alloy 20 stainless steel threaded rods contain nickel to withstand exposure to sulfuric, phosphoric, and nitric acids.

About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.

These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

These Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

Unlike metal rods, these metric threaded rods will not warp at extreme temperatures, making them ideal for heat treating and furnace fixtures.

Fiberglass threaded rods are stronger than nylon threaded rods. They resist acids, solvents, salt water, and oil.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

More corrosion resistant than 400 nickel threaded rods, these C276 nickel rods are often used in marine environments and chemical-processing plants.

Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.

Commonly used in valves, pumps, and shafts, these 400 nickel threaded rods resist salt water and caustic chemicals.

A hex drive on one end allows these rods to be turned with a hex key for ease of installation.

Weld these studs to uncoated steel surfaces.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

Also known as hood pins, these studs have a cotter pin lodged through a drilled hole in the unthreaded portion for light duty holding, such as securing access panels and locking other fasteners.

316 stainless steel studs have excellent resistance to chemicals and salt water.

These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

Add a stud to thin material when you only have access to one side.

These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.

Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.

Bolts are beveled under the head for use in countersunk holes.

A shallow head makes these bolts good for low-clearance applications.

These anchors fit a range of sheet metal and wood screw sizes since they form their own threads when installed.

Fins prevent these anchors from spinning during installation.

A drilled hole is required for installation.

An open-end cap nut provides a finished appearance.

Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.

These 18-8 stainless steel anchors have good chemical resistance.

These 18-8 stainless steel anchors have good chemical resistance.

Also known as tap-in or uni-tap rivets, these anchors are barbed to resist pull out. Made from nylon, they're chemical resistant.

Use in applications requiring high strength.

Also known as drive rivets, install these anchors by hammering the pin into the body. Pry out the pin to remove.

A tamper-resistant nut prevents unwanted removal of the object you are anchoring.

A zinc plating provides corrosion resistance in wet environments.

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Also known as lag shields, these anchors are designed for use with large-diameter wood screws.

Also known as mungo anchors, these have large fins that prevent rotation.

Use with any type of sheet metal or wood screw.

Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.

A pivoting toggle bar creates a strong hold.

These steel anchors are available with corrosion-resistant finishes.

These steel anchors are available with corrosion-resistant finishes.

Bolts are beveled under the head for a flush finish in countersunk holes.