Configure a connector for your application—combine inserts for power and signal with a base and a hood.

Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Protect mini connectors when not in use.

Join two connectors that both have internal threads.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Simplify wiring and reduce the number of cords in your automation setup.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Protect screw-together M12 connectors when not in use.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

To save space and reduce the number of cords in industrial automation setups, these splitters join two devices with M12 connectors to a single cord, distribution block, or I/O module with M12 connectors.

Visually confirm your connector is working properly. A green light means your connector has power, while yellow means it has signal.

Minimize signal loss between low-current devices with M8 connections.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place.

Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. Use them with standard Molex connectors.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

Protect Mil. Spec. connectors when not in use.

Quickly replace or add connectors to an existing wiring system—connectors come assembled with wire leads already installed. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Configure a connector for your application by combining housings with pins and sleeves for different wire sizes. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Made with industry standard barrel-style ends, these connectors carry DC power between electronic devices and power supplies.

Choose a socket that works with your Siemens servomotor system.

Mount these receptacles to control cabinets and equipment in order to quickly connect and disconnect M29 power cords.

Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.

Protect plugs and sockets in washdown environments when not in use.

Caps are watertight to protect hazardous location safe-break plugs when not in use.

Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.

Reduce the number of electrical connections in sanitary areas, such as food plants—these connectors combine Ethernet, a power cable, and wire for signals into a single connection point.

Caps are watertight to protect safe-break plugs when not in use.

Meet international standards IEC 309-1 and 309-2.

Connect and disconnect your equipment all at once.

One hand is all you need—just push these connectors in to secure them and charge surveillance cameras, user interfaces, and other small devices.

A threaded M8 end on these connectors keeps contaminants out and withstands vibration better than RJ45 ends on traditional Ethernet cords.

Replace damaged connectors on lighting cables that are commonly used for movie and stage lighting, as well as interior building lighting.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

Send signal and data to operate, measure, or regulate automated equipment such as conveyors and CNC machines.

This cable is used in variable-frequency drive motors. It has shielding to block signal interference caused by voltage fluctuations and current spikes.

Nearly two-thirds the diameter of standard control cable, this cable fits in tight spaces. It sends signal and data to operate, measure, or regulate automated equipment.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

In addition to handling continuous movement, this cable withstands twisting up to 450° without degrading data or signal transmission. It's often used in welding robots and rotary tables.

Connect servocontrollers and servomotors in automated equipment and on assembly lines. This cable withstands continuous motion without degrading data or signal transmission.

Often used in automated applications such as robotics and cable carriers, this cable withstands continuous motion without degrading data or signal transmission.

The insulation resists corrosive chemicals and salt water, and the wires in this cable are tin plated for corrosion resistance.

A braided bronze armor provides excellent protection against abrasion and other damage. The wires are tin-plated for corrosion resistance, and the insulation resists corrosive chemicals and salt water.

Often used in automated applications that require continuous motion, this cable sends data between computers, servers, and switches without degrading signal transmission.

Often used for automated systems, motors, and pumps in tough industrial areas such as near welding and metal machining, these cords carry higher current than M5, M8, and M12 cords.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Compatible with Molex connectors, these cords are sized to fit in tight spaces. They're often used in the interior of machines.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

Often used in assembly line networks and Fieldbus connections, these cords have B-coded M12 connections.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs).

Send high-speed data between sensors, switches, or I/O modules with an M8 connection and programmable logic controllers (PLCs) and computers with a traditional RJ45 connection.

Filled with gel, these wire taps seal out moisture.

Tap and splice multiple wires in temporarily wet environments and up to six feet underground.

Push stripped wires into connectors for a reliable connection that's faster to install than twisting or crimping.

Use a single splice to connect more than two wires.

Connect these lifters to your robot arm to pick up and move items using suction. They're electric, so you don't need a compressed air source.