We will reply to your message within an hour.
Use this wire in ovens, furnaces, and other electrical heating equipment where temperatures reach 480° F and higher.
These adapters provide electromagnetic interference (EMI) protection when connecting shielded flexible plastic conduit to a knockout in an outlet box or enclosure.
Commonly used for eyeglass frames and antennas, this wire bounces back to its original shape after bending, stretching, and twisting.
Bend this wire and it will hold its shape until you heat it. It is commonly used in automotive switches and latches.
This nickel-chromium, often called Chromel C, provides effortless formability. Use it for heating elements, resistance windings, and hot-wire cutters.
Bend this wire and it will stay in place. It is often used as safety lock wire.
Able to withstand temperatures up to 1000° F, 600 nickel is often used as safety lock wire in high-temperature applications. It is comparable to Inconel.
These nickel-iron-cobalt alloy rods expand at the same rate as glass when heated. They offer better machinability than Invar 36 and are often used anywhere a dependable glass-to-metal seal is required, such as in diodes and microwave tubes.
This copper wire is clad in nickel to provide excellent corrosion resistance at temperatures up to 1200° F while maintaining high electrical conductivity.
This wire rope provides a good balance of abrasion resistance and flexibility.
More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.
The superior corrosion resistance of nickel-copper makes this braided wire best for use with salt water and acidic- and alkaline-based solutions.
Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.
Feed the wire rope into the opening at the bottom of these hook-end fittings and through the body for a quick and simple installation.
Feed the wire rope into the opening at the bottom of these clevis-end fittings and through the body for a quick and simple installation.
Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.
Often used to repair pipe, this wire joins nickel alloys to themselves and to stainless steel and steel.
Often used to repair pipe, these rods join nickel alloys to themselves and to stainless steel and steel.
Rosin flux is quick acting with strong cleaning action, but it leaves residue that requires flux remover.
The five flux cores allow fast soldering that uses less solder and transmits less heat to the joint. Rosin flux is quick acting with strong cleaning action but leaves residue that requires flux remover.
The flux leaves minimal residue so there's no need for cleanup.
Acid flux has strong cleaning action, but leaves corrosive residue that washes away with water.
Wash away flux residue from this solder with water.
Electrically conductive, this solder is best for electronics and electronics applications.
This solder is commonly used in solder melting pots
This solder is commonly used in solder melting pots.
The high melting point prevents remelting when soldering successive joints with another solder.
Rosin flux is quick acting with strong cleaning action, but leaves residue that requires flux remover.
Even as temperatures approach absolute zero, this indium solder remains soft and malleable, allowing it to form an airtight seal between metal and certain non-metal materials..
Made with indium this solder is soft and malleable—even as temperatures approach absolute zero—allowing this solder to form an airtight seal between metal and certain non-metal materials. Thanks to its ribbon shape, this solder is easier to use on large, flat areas than wire solder.
Use this solder for general purpose applications.
This solder keeps its strength in applications where vibration and frequent and extreme temperature changes occur, such as in water lines and refrigeration equipment.
The flux leaves minimal residue so there's no cleanup.
The flux residue easily washes away with water.
The silver in this solder helps it resist vibration to form strong joints in HVAC systems. Since it doesn’t have a flux core, you can choose the flux that works best for your application.
This bismuth-tin solder has similar performance properties to lead solder, but is also safe for use in food-processing equipment and copper water pipes.
This solder meets NSF/ANSI Standard 61 for drinking water.
Also known as solder slugs, these pellets create strong, electrically conductive connections between battery terminal lugs and cable.
Use these cadmium-free alloys with most metals in general purpose applications.
No need to add flux—these alloys have it built in.
Use these alloys with most metals in general purpose applications.
Join metal in inert atmospheres or vacuum conditions, such as furnace brazing.
Create stronger bonds than standard brazing alloys.
Use these alloys on metal subject to corrosion.
To fill in large gaps, these BAg-2 alloys melt into a thicker liquid than standard brazing alloys.
When melted, these alloys form a thin liquid that easily flows into smaller gaps than standard gap-filling brazing alloys.
Fill in tight gaps without needing to add flux before you braze—these alloys have flux built in. When melted, these alloys form a thin liquid that easily flows into smaller gaps than standard brazing alloys.
Everything you need to start brazing most metals in general purpose applications.