Assortments contain threaded pipe in various lengths.

Made of galvanized steel, this Schedule 40 pipe has fair corrosion resistance and is designed for low-pressure applications.

Assortments contain threaded pipe in various lengths.

Typically used with medium-pressure galvanized iron and steel threaded pipe fittings. Also known as Schedule 80.

Made to tighter tolerances than other steel pipe fittings, these are also known as instrumentation fittings.

Typically used with high-pressure iron and steel threaded pipe fittings. Also known as Schedule 160.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.

Typically used with extreme-pressure iron and steel unthreaded pipe fittings. Pipe is also known as Schedule XXH .

Low-profile barbs and a longer first barb allow for a smoother, easier installation than other barbed fittings. Slide the barbed end into hose and secure with a clamp.

Kits contain Industrial quick-disconnect plugs in four coupling sizes so you can determine the size of your couplings without needing to measure.

Also known as automotive couplings. Compatible with Tru-Flate-shape plugs and sockets.

Compatible with ARO-shape plugs and sockets.

A slim body allows these couplings to fit into tight spaces. Compatible with Compact-shape plugs and sockets.

Compatible with Lincoln-shape plugs and sockets.

These couplings have a lower profile than other claw-style couplings to fit in cramped spaces. They consist of a plug and a socket that connect with a quarter twist. Also known as Bowes couplings.

Also known as live swivels, these fittings swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 5,000 psi.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Use these couplings at pressures up to 6,500 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with Snap-Tite H-Shape plugs and sockets.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO A-shape plugs and sockets.

Use these couplings at pressures up to 7,200 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with International Standard ISO Minimal-Spill-shape plugs and sockets.

Couplings consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are designed for coolant applications up to 200 psi. Also known as coolant-line mold couplings.

Also known as ground-joint couplings and boss couplings, these fittings are designed for high-pressure steam applications up to 600 psi. Insert the barbed end of the fitting into hose, then position the interlocking clamp over the hose and bolt into place. The clamp firmly grips your hose as it locks into the ring of the barbed end, creating a leak-tight seal.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Prevent damage to bearing seals caused by over-lubrication—these fittings automatically stop grease flow when pressure is within the shut-off range.

Use these fittings in tight spaces where protruding fittings won't work.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. They're also known as hydraulic grease fittings.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.

Lubricate multiple points from a single location.

Tap these tools once or twice with a hammer to install fittings.