Fiberglass screws are stronger than plastic screws, chemical and oil resistant, nonconductive, and lightweight.

These screws are chemical and oil resistant, nonconductive, and lightweight. The flange eliminates the need for a washer, distributing pressure where the screw meets the surface.

A high-strength alternative to blind rivets, use these screws when only one side of the material is accessible.

Seal out contaminants and prevent leaks—a rubber O-ring under the head prevents leaks and seals out contaminants.

Made from nylon, these metric pan head screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Reliable in harsh environments up to 500° F, PEEK screws withstand acids, bases, and salt solutions. They are chemical and oil resistant, nonconductive, and lightweight.

Made from polycarbonate, these metric pan head screws resist breaking in high-impact applications. They are chemical and oil resistant, nonconductive, and lightweight.

Nylon screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

PTFE screws withstand harsh chemicals and temperatures from -100° F to 500° F. They are nonconductive, lightweight, and resist wear due to their slippery surface.

Nylon screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Made from nylon, these screws are chemical and oil resistant, nonconductive, and lightweight.

To prevent unwanted removal, these metric screws have a tamper-resistant Torx drive—also known as a pin-in Torx drive—that makes them difficult to unscrew without special tools. An O-ring under the head blocks leaks and seals out dust and dirt.

A rubber O-ring prevents leaks and seals out contaminants. Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic.

A nylon patch bonded to the threads adds friction to resist loosening from vibration.

These metric screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

These metric polycarbonate screws resist breaking in high-impact applications better than other plastic screws. All are chemical and oil resistant, nonconductive, and lightweight.

These screws are more reliable in high-stress, high-temperature environments than other plastic screws. They withstand water, steam, and temperatures up to 500° F.

With an O-ring under the head, these metric screws seal out leaks and contaminants while also preventing unwanted removal.

To prevent leaks and seal out contaminants, these metric screws have an O-ring under the head.

Made from 18-8 stainless steel, these screws are chemical resistant.

Able to penetrate overlapping sheets, these screws have a secure hold in wood.

Cutting wings under the head allow plastic to expand and contract without cracking. A washer made from aluminum and rubber bonded to steel adds a watertight seal.

18-8 stainless steel screws have good chemical resistance.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

A large head allows you to grip these screws with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Tighten these thumb screws by hand or with a hex key for more torque.

A raised head makes these thumb screws easy to grip. Made from nylon, they're chemical resistant, nonconductive, and lightweight.

A thin head allows these thumb screws to be used in low-clearance applications.

Made from nylon, these set screws are lightweight, resist chemicals, and won’t carry an electric current.

Plastic binding barrels and caps are chemical resistant, nonconductive, and lightweight.

These rounded head nuts can be riveted into thin panels for a flush fit. They can be mounted without spaces between the panels. A quarter-turn locks and releases access panels, doors, and covers.

These rounded head screws have a nut that clips onto the edge of a thin panel, allowing you to mount the screw near edges. A quarter-turn locks and releases access panels, doors, and covers.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

These acetal threaded rods won't absorb moisture like nylon and fiberglass rods, so they're good for use in wet environments. They resist alcohol, gasoline, and solvents.

Also known as mungo anchors, these have large fins that prevent rotation.

These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.

Easy to install, tap these anchors in like a nail—no drilled hole required.

Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.

Install these spring plungers with a screwdriver—they're slotted on one or both ends.

An O-ring in the flange creates a tight seal.

Use these eyebolts for routing wire and for other light duty applications.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

Made of impact-resistant nylon, these externally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

A double row of precision ball bearings allows high speeds and smooth operation.

In addition to offering superior chemical resistance, these lightweight, fiber-reinforced nylon rod ends also reduce noise and vibration.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel and zinc ball joint linkages.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

Conceal and protect the tops of socket head or button head screws.

To conceal and protect the entire screw head, insert your screw through the hole in the base and snap on the top.