Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

An easy-to-read flow-indicating handle shows the percentage the valve is open. These valves are for use with water, oil, inert gas, and steam.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

For installation in instrument panels, these valves have threads and a hex nut below the handle. They’re for use with water, oil, air, and inert gas.

Often used in high-purity applications, such as oxygen service, these valves come cleaned and bagged. Use with water, oil, inert gas, and steam.

Use these valves with garden hose and other landscaping equipment. They’re for use with water, air, and inert gas.

Install these low-profile valves in tight spots. They are for use with water, oil, air, and inert gas.

Also known as wafer ball valves, these combine the slim body of a butterfly valve with the high flow rates of a flanged ball valve. They bolt to ANSI flanges. Use with water, oil, air, inert gas, and steam.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

For a leak-tight connection that doesn’t require heat or soldering, these valves have press-connect fittings that crimp to metal tubing with a press-connect crimping tool.

Service these valves without cutting soldered connections. The three-piece bolted body can be disassembled inline for easy access to internal components. Use with water, oil, inert gas, and steam.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61 for use in drinking water lines.

Use these valves with garden hose and other landscaping equipment. All meet NSF/ANSI 61 for use with drinking water.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

Solder these valves to metal tubing for a permanent, leak-tight connection. They meet NSF/ANSI 61 for use with drinking water.

With a fluoroelastomer seal and a CPVC body, these valves can withstand aggressive and corrosive solutions in chemical-processing applications.

Attach gauges or sensors to these valves so you can remove them for maintenance and calibration without depressurizing your line. They are also known as block and bleed valves.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

There’s no need to unbolt these valves for cleaning—remove the valve handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body to withstand aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. All have a PTFE seal and a corrosion-resistant 316 stainless steel body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the push-to-connect fittings on these valves—no heat, solder, or flux required. They meet NSF/ANSI 51 for safe use with food.

3-A certified as meeting sanitary design standards, these valves control the flow of liquids in food, dairy, pharmaceutical, and cosmetic plants.

These valves have 37° flared tube fittings that form a tight seal on metal tubing lines to transfer diesel fuel, fuel oil, and gasoline.

Install these low-profile valves in low-clearance pipelines for natural gas, propane, and butane.

To create a tight seal in vacuum conditions higher than 29.9” Hg, these valves have ultra-high-vacuum tube fitting connections, which are also known as KF, QF, and NW fittings. They are often used in applications such as vacuum coating and heat treating, leak testing, and analyzing gases.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

Their ball-valve design allows these valves to handle three times the flow of butterfly valves.

Also known as actuated ball valves, these provide higher flow rates than other air-driven valves.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

Slide copper pipe into the solder-connect fittings on these valves and weld for a strong, permanent connection.

These valves have threaded NPT connections.

For three times the flow of butterfly valves, these have a ball valve design.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

Barbs grip onto tubing, providing a secure hold. Use with water, oil, air, and inert gas. These valves divert flow between ports in tubing lines.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

Barbed fittings on these valves grip onto tubing, providing a secure hold. To divert flow between ports in chemical-processing applications, they have a chemical-resistant seal and a PVDF body to withstand aggressive and corrosive solutions.

With sanitary quick-clamp connections for easy disassembly in systems that require frequent cleaning, these valves are often used to divert flow between ports in food and beverage applications.

Barbed fittings on these valves grip onto tubing, providing a secure hold. They divert flow between ports in food and beverage tubing lines.

To test water quality without interrupting flow, drain a small amount of liquid through the sampling outlet.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

For food and beverage systems that require frequent cleaning, these valves have sanitary quick-clamp connections for easy disassembly. They operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

These valves open to allow flow in one direction and close when flow stops or reverses.

Barbs grip onto tubing, providing a secure hold.

Plastic provides a lightweight alternative to metal.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection.

With a shorter end-to-end length than other check valves, these fit in tight spaces.

Plastic provides a lightweight alternative to metal.

Insert tubing into the fitting—no heat, solder, or flux required.

To withstand high pressures and temperatures in steam service applications, these valves have a 316 stainless steel body, PTFE ball, and PTFE seal.

The metal body is more durable than plastic.

Attach these balancing valves using solder—they help you measure the difference in pressure across the valve and adjust the flow rate to system components. Also known as circuit setters, they’re often used in systems that need an even distribution of flow, such as HVAC systems.

Lock the handle using a padlock.

Also known as check valves, these open to allow flow in one direction and close when flow stops or reverses.

Control flow in two directions from a single source—these valves have two balls for independent control and shut-off of each outlet.

When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle. They close and send a signal to turn the device off when pressure drops.