These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

Use with coolant and detergent such as ethylene glycol or soap solutions.

Reduce your pipeline footprint with these low-profile valves that are about half the size of standard valves for coolant.

Sturdy internal components resist wear for a long service life in applications with frequent cycling.

Designed to withstand the high temperatures and pressures in steam service applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

Available in smaller pipe sizes than other solenoid flow-adjustment valves, these are often used with gas chromatography equipment and analytical instrumentation. They adjust and regulate flow based on the intensity of the electrical signal into the valve. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Direct flow with an electronic signal.