These are also known as tappet wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

These wrenches are made of stainless steel for excellent corrosion resistance.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

A ratchet mechanism in the heads lets you turn fasteners in tight spaces without removing and repositioning the wrench.

The head is offset 45° to provide additional clearance when reaching over obstructions.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These lightweight tools are also known as AN (Army-Navy) wrenches.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

When turning fasteners in small spaces, these short wrenches fit where others can't.

A lever reverses the ratchet direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Suitable for occasional maintenance work, these sets are imported.

Flip these wrenches over to ratchet in the opposite direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Quickly find the wrenches you're looking for with these brightly colored sets.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

These wrenches are made of stainless steel for excellent corrosion resistance.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

Turn the knob to adjust the jaws and fit a range of fastener sizes.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

The 25° offset heads give you additional clearance to turn hard-to-reach fasteners.

The head is offset 45° to provide clearance for reaching over obstructions.

Also known as slugging wrenches, strike the handle with a hammer to break stuck fasteners free.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

The long handle provides extra leverage—add an extension to increase it even more.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

Also known as half-moon and obstruction wrenches, the shape lets you reach around obstacles and into machinery.

The heads are offset to provide clearance for reaching over obstructions.

The heads are offset 45° to provide clearance for reaching over obstructions.

Fit the thin head and long jaws into narrow spaces.

The adjustment knurl won't turn when the wrench is being used, preventing accidental loosening of the jaws.

The handle is covered in plastic for a comfortable grip.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.

Extend the handle for additional reach.

Squeeze the handles and the gripping surfaces adjust to fit your fastener and prevent slipping and stripping.

Also known as spud, structural, and construction wrenches, the pointed end of the handle aligns bolt holes during assembly.

Reverse the movable jaw to convert from a smooth-jaw adjustable wrench to a serrated-jaw pipe wrench.

The head pivots to accommodate a range of diameters.

These wrenches are made of stainless steel for excellent corrosion resistance.

Sets include various sizes of wrenches that fit into slots on the circumference of collars, bearings, and other machine tool components.

The head pivots to accommodate a range of diameters.

Sets include various sizes of wrenches that are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.

The slim profile fits the flanges and nuts on the backing pads of portable sanders and grinders.

Use your ratchet wrench as a handle.

Grip the round holes on the face of collars, bearings, and other machine tool components.