These locknuts are about half the height of standard nylon-insert locknuts. Use them in light duty low-clearance applications or jam one against a hex nut to hold it in place. The nylon insert grips the bolt to resist loosening without damaging threads. They're reusable, but their holding power lessens with each use.

Zinc-plated steel locknuts resist corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.

Half the height of standard nylon-insert locknuts, use these locknuts in low-clearance applications or jam one against a hex nut to hold it in place. The nylon insert grips the bolt to resist loosening without damaging threads. They're reusable, but their holding power lessens with each use. These nuts are suitable for fastening most machinery and equipment when used in conjunction with a standard hex nut. All have a finish that resists corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.

These locknuts have good chemical resistance and may be mildly magnetic. They're about half the height of standard nylon-insert locknuts. Use them in low-clearance applications or jam one against a hex nut to hold it in place. The nylon insert grips the bolt to resist loosening without damaging threads. They're reusable, but their holding power lessens with each use.

For technical drawings and 3-D models, click on a part number.

These locknuts are about half the height and 10% wider than standard nylon-insert locknuts. Use them in light duty low-clearance applications or jam one against an extra-wide hex nut to hold it in place. The nylon insert grips the bolt to resist loosening without damaging threads. They're reusable, but their holding power lessens with each use.

Zinc-plated steel locknuts provide mild corrosion resistance in wet environments.

For technical drawings and 3-D models, click on a part number.

These locknuts are about 10% wider and taller than standard nylon-insert locknuts and distribute the load over a large area. The nylon insert grips the bolt to resist loosening without damaging threads. They're reusable, but their holding power lessens with each use. Use them in light duty fastening applications, such as securing access panels. A zinc plating provides corrosion resistance in wet environments.

For technical drawings and 3-D models, click on a part number.

An irregularly shaped thread at the top of the nut grips the bolt for a stronger hold than nylon-insert locknuts. They thread on from the bottom of the nut, allowing more threads to engage the bolt before tightening for easier installation than center-lock distorted thread locknuts. The strength of the bolt should match the strength of the nut to prevent damaging threads. They're not reusable. Comparable in strength to Grade 8 bolts, they're about 25% stronger than medium-strength steel locknuts.

Black-phosphate, zinc-plated, and zinc yellow-chromate plated locknuts resist corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.

Secure these hex slotted nuts by inserting a cotter pin or safety wire through the slots and a drilled hole in your bolt for mild loosening resistance. They’re not recommended for use on parts exposed to high vibration because the pin is prone to shearing under prolonged stress. Height includes the slots. Cotter pins are not included. They're zinc plated to resist corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.

These locknuts have good chemical resistance and may be mildly magnetic. Also known as castle nuts, secure them by inserting a cotter pin or safety wire through the slots in the nut and a drilled hole in your bolt for mild loosening resistance. They’re not recommended for use on parts exposed to high vibration because the pin is prone to shearing under prolonged stress. Height includes the slots. Cotter pins are not included.

For technical drawings and 3-D models, click on a part number.

When installed, the steel insert grips the threads and lifts away from the nut body, isolating the insert from the nut’s load to resist spinoff caused by vibration. These locknuts are often used in shakers and vibrating equipment. The strength of the bolt should match the strength of the nut to prevent damaging threads. Made from Grade 5 steel, they're suitable for fastening most machinery and equipment.

For technical drawings and 3-D models, click on a part number.

These locknuts are about 10% wider and taller than standard steel-insert locknuts. They distribute the load over a large area. When installed, the steel insert grips the threads and lifts away from the nut body, isolating the insert from the nut’s load to resist spinoff caused by vibration. They're often used in shakers and vibrating equipment. The strength of the bolt should match the strength of the nut to prevent damaging threads. Made from Grade 8 steel, they're about 25% stronger than medium-strength steel locknuts.

Zinc yellow-chromate plated steel locknuts resist corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.