About half the height of standard-profile locknuts, these fit in spaces with low clearance. You can also use them as jam nuts by threading them against a hex nut to hold it in place. The nylon insert grips the screw to prevent loosening from moderate vibration without damaging threads. However, the insert may become brittle if exposed to high temperatures. These locknuts are reusable a handful of times, but the holding power decreases with each use.

These locknuts are manufactured and tested to strict U.S. military standards for material and construction. The nylon insert grips the screw to prevent loosening from moderate vibration without damaging threads. However, the insert may become brittle if exposed to high temperatures. These locknuts are reusable a handful of times, but the holding power decreases with each use.

These locknuts are manufactured and tested to strict U.S. military standards for material and construction. They are about half the height of standard-profile locknuts to fit in spaces with low clearance. You can also use them as jam nuts by threading them against a hex nut to hold it in place. The nylon insert grips the screw to prevent loosening from moderate vibration without damaging threads. However, the insert may become brittle if exposed to high temperatures. These locknuts are reusable a handful of times, but the holding power decreases with each use.

Irregularly shaped threads at the top of these locknuts grip the screw for a stronger hold than nylon-insert locknuts. Although the threads prevent the nut from backing out due to vibration, they also increase the effort to install and remove. To get these nuts off, you may need special tools, such as an impact wrench or propane torch. Nuts are not reusable.

Also known as reversible locknuts, these thread on from either side, so you don't have to worry about fastening them incorrectly and damaging your screw. The irregularly shaped threads in the middle grip the screw for a stronger hold than nylon-insert locknuts. Although the threads prevent the nut from backing out due to vibration, they also increase the effort to install and remove. To get these nuts off, you may need special tools, such as an impact wrench or propane torch. Nuts are not reusable.

To save on assembly time, these locknuts combine a hex nut with a free-spinning lock washer, so you can twist them into place by hand. Once the nut is against your material surface, tighten it down with a wrench or socket to get the teeth to bite. Although these nuts install more quickly than nylon-insert locknuts, they don't hold up as well against vibration and can mar your material. As long as the washer stays intact, you can reuse them. Also known as Keps and K-lock nuts.

Use these locknuts to secure rotating parts subjected to mild vibration, such as the wheels on carts and hand trucks. They’re not recommended for use on parts exposed to high vibration because the pin can shear under prolonged stress. These nuts are reusable, but you'll need a new cotter pin (not included) with each use.

The top section of these nuts expands to grip the screw on all sides for a stronger hold than both nylon-insert and distorted-thread locknuts. They’re often used in equipment with constant, vigorous vibration, such as engines. These locknuts are reusable a handful of times, but the holding power decreases with each use.

About two-thirds the height of standard flex-top nuts, these fit in spaces with low clearance. You can also use them as jam nuts by threading them against a hex nut to hold it in place. The top section expands to grip the screw on all sides for a stronger hold than both nylon-insert and distorted-thread locknuts. As a result, they're suitable for use in equipment with constant, vigorous vibration, such as engines. These locknuts are reusable a handful of times, but the holding power decreases with each use.

These locknuts are manufactured and tested to strict U.S. military standards for material and construction. The top section expands to grip the screw on all sides for a stronger hold than both nylon-insert and distorted-thread locknuts. As a result, they're suitable for use in equipment with constant, vigorous vibration, such as engines. These locknuts are reusable a handful of times, but the holding power decreases with each use.

Similar to steel-insert locknuts, these two-piece nuts withstand extreme vibration but are easier to install. Since the two pieces spin freely by hand until you tighten them together with a wrench, they're perfect for extra long screws and threaded rods. You can reuse them a handful of times, but their hold will decrease with repeated use. Also known as drake-style locknuts.

Height includes both nuts once assembled.

Serrations bite into material for mild vibration resistance while the flange eliminates the need for a separate washer. These nuts are ideal for securing screws in oversized or irregularly shaped holes since the flange covers a larger area than standard nuts. You can use them again and again without sacrificing strength. However, the serrations may mar the surface of your material. Also known as collar nuts.

A nylon insert grips the screw for a stronger hold than a serrated flange, without damaging threads or marring the surface of your material. However, the insert may become brittle if exposed to high temperatures. These nuts have a flange that distributes pressure evenly across the mounting surface, so you don't need a separate washer. They are ideal for securing screws in oversized or irregularly shaped holes since the flange covers a larger area than standard nuts. You can reuse them a handful of times, but their holding power will decrease with each use. Also known as collar nuts.