Add strong threads in soft metal, such as aluminum. The keys on these inserts drive into holes to hold more securely than thread-locking or helical inserts. They prevent slipping and rotating, so they’re stable enough for use in vehicle or aerospace parts that experience heavy vibration. These inserts are comparable to Keensert inserts.

To install, drill and tap a hole in your material. Then, thread the insert onto the installation tool and screw it into the hole. Place the tool over the keys and hit it with a hammer to drive them in.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench. You can also use them to increase or reduce your thread size, or to create space between parts in an assembly.

Smoothly install these inserts for strong threads near the edges and corners of soft metal surfaces. They’re lubricated to prevent sticking as you thread them in. Since these have thinner walls than our key-locking and thread-locking inserts, they don’t need as much space and won't bulge or crack the material. The knurls press (swage) into the material to keep inserts in place when you tighten or loosen a screw.

To install these inserts, you need a drill bit, a counterbore, a standard tap, an installation tool, and a hammer. Drill a hole, counterbore the top, and tap it. Place the insert into the installation tool, then hand-tighten it into the tapped hole. Strike the tool to secure the insert and drive the knurls into the surrounding material.

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench. The threads on these adapters have various sizes and spacing, so you can increase or decrease thread size or adapt from coarse to fine threading. You can also use them to change the gender of a connection from male to female. Small adapters can work as threaded standoffs, which position and separate circuit boards and other components in assemblies.

Change thread sizes or types, such as fine to coarse threads, on parts without changing gender. These adapters can also be used as standoffs to position components in assemblies and to create space between parts. They have an external hex, so you can tighten them with a wrench.

Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection. You can also use these adapters to change the gender of a mating part from female to male, increase or decrease the thread size, or convert the threads from fine to coarse (and vice versa). The smaller adapters act as threaded standoffs, positioning and separating circuit boards and other components in assemblies.

Restore, reinforce, or create threads in metal. The tough coils on these inserts expand once installed to anchor in a tapped hole. Also known as Heli-Coil inserts, they're often used in engine heads and machinery housings where strong connections are critical. Unlike threadlocking inserts, you can remove and reuse them without them losing their strength.

Installation requires a drill bit, a helical insert tap, and an installation tool.

The irregularly shaped threads tightly grip screws to prevent them from loosening or backing out under vibration. Use these inserts to create or repair threads in pumps and other machinery that shakes and rattles. Also known as Heli-Coil inserts.

Installation requires a drill bit, a helical insert tap, and an installation tool.

Create the tightest hold in aluminum and other soft metal without screws sticking. The lubricant on these inserts eases installation, and the irregularly shaped threads won’t let screws back out from vibration. Inserts have keys that drive into material to prevent them from slipping or rotating in the hole.

To install, drill and tap a hole in your material. Then, thread the insert onto the installation tool and screw it into the hole. Place the tool over the keys and hit it with a hammer to drive them in.

Add strong threads to the edges of soft metal without bulging or cracking the material. These inserts have thinner walls than our key-locking and thread-locking inserts, so they don’t need as much space around them. The knurls press (swage) into the material to keep inserts in place when you tighten or loosen a screw.

To install these inserts, you need a drill bit, a counterbore, a standard tap, an installation tool, and a hammer. Drill a hole, counterbore the top, and tap it. Place the insert into the installation tool, then hand-tighten it into the tapped hole. Strike the tool to secure the insert and drive the knurls into the surrounding material.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench. Small adapters can also be used as standoffs, positioning and separating circuit boards and other components in assemblies.