A nylon insert keeps metric bolt threads from coming loose due to vibration, wear, and temperature swings. About 25% stronger than medium-strength steel locknuts, these nuts are made of high-strength, Class 10 steel. They're used in valves, pumps, suspension systems, and other high-stress parts. A zinc plating prevents rust in wet areas. Combine with Class 10.9 metric bolts, which have similar strength. All are reusable but lose holding power after each use.

These locknuts meet ISO 7040 and ISO 7041-2 (formerly DIN 985 and DIN 982), which are international standards for dimensions. The ISO standards are functionally equivalent to the DIN standards with slight differences in width, height, or tolerances.

For technical drawings and 3-D models, click on a part number.

Get a grip on metric bolts exposed to vibration, wear, and changes in temperature. These metric locknuts have a nylon insert that holds onto bolts without damaging their threads. They have fine-pitch threads, which are closer together than coarse-pitch threads and less likely to loosen from vibration. Fine threads and coarse threads are not compatible. These locknuts are reusable but lose holding power with each use.

Made of Class 8 steel, these nuts are strong enough for use with most machinery and equipment. A zinc plating prevents rust in wet and damp areas. Combine them with Class 8.8 metric bolts, which are comparable in strength.

These locknuts meet the dimensional and material standards of DIN and ISO that make sure they're compatible with other parts and tools. Although DIN 982 and 985 are no longer active standards, they’re still a common reference point for designers. With only slight differences in tolerance, ISO 7041-2 and 7040 have replaced the inactive DIN standards.

For technical drawings and 3-D models, click on a part number.

Internal ball bearings provide smooth low-friction travel in applications that require high speeds, accurate positioning, and repeatable movement. Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts. To ensure compatibility, select components that have the same thread size and pitch. Ball nuts are furnished with a tube to keep ball bearings in place. Do not remove the tube until you are ready to install the nuts onto the screws.

Travel distance per turn, also known as screw lead, is the distance a ball nut moves with one revolution of the ball screw.

For technical drawings and 3-D models, click on a part number.

Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench. Made of carbon steel, they’re strong and wear resistant.

Use stepped-face retaining nuts with DIN 462 spring lock washers. You can also use them in pairs or with other bearing retaining nuts as jam nuts. For the nut closer to the bearing, position the stepped face towards the bearing. All meet DIN standards for bearing lockout dimensions.

Chamfered-face retaining nuts weigh less and produce less heat than stepped-face nuts. They meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.

For technical drawings and 3-D models, click on a part number.

Used in pairs or with another bearing retaining nut, these jam nuts—often called shaft nuts—hold bearings, bushings, pulleys, and gears in place on your threaded shaft or spindle. Threading two nuts tightly against each other makes it harder for vibration to loosen your assembly than if you used only one nut. For the nut closer to the bearing, position the stepped face towards the bearing. These jam nuts have holes on the side, so you can tighten and loosen them with a pin spanner wrench. Made of carbon steel, they’re strong and wear resistant. All meet DIN 1816, an international standard for bearing locknut dimensions.

For technical drawings and 3-D models, click on a part number.