Suitable for marine environments, this cord resist corrosion from salt water and chlorine.

Contain and organize bulky and oddly shaped loads with these nets.

All-nylon construction allows this rope to compensate for sudden force.

Use this nylon rope when you need to compensate for sudden force, such as in towing applications or dock lines.

Also known as sash cord, this rope has a soft cotton cover, so you can grip it without hurting your hands.

The braided construction makes this twine more wear resistant and less likely to unravel than twisted twine.

Also known as fishing line, this line is very thin, yet strong and wear resistant.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

These grips are sized to fit in tight areas.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Tighten the screw-down clamp for superior pull-out resistance.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

Protect cords routed through holes in enclosures and panels.

Just like the material found in wetsuits, these neoprene foam sheets are encased in nylon fabric for additional protection from wear caused by rubbing and abrasion.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

Designed for extreme wear resistance, this Kevlar-filled nylon 6/6 material lasts up to 20 times longer than unfilled nylon. Also known as Hydlar Z, it is often used for parts that are continuously exposed to wear and abrasion, such as wear strips and bushings.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

The addition of MDS gives these tubes exceptional wear resistance along with a self-lubricating surface. They're made of cast nylon 6, making them easier to machine and better electrical insulators than other MDS-filled nylon tubes.

The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

Secure glasses to a cord to hang them around your neck.