System of Measurement System of Measurement |
---|
|
Construction Construction |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
Component Component |
---|
|
Application Application |
---|
|
Connection Type Connection Type |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
Carabiner Material Carabiner Material |
---|
|
Nylon Lanyards—Not for Lifting

These all-plastic lanyards are an economical alternative to rope and wire rope lanyards.
Warning: Test all assemblies for required strength before use.
For technical drawings and 3-D models, click on a part number.
Eye | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Rope Dia. | Lg. | Loop Inside Lg. | Max. Loop Inside Lg. | ID | Thick. | For Screw Size | Temperature Range, °F | Capacity, lbs. | Color | Pkg. Qty. | Pkg. | |
Loop × Loop | ||||||||||||
3/32" | 8" | 1 1/2" × 1 1/2" | __ | __ | __ | __ | -22° to 150° | 7 | Black | 10 | 00000000 | 00000 |
3/32" | 10" | 1 1/2" × 1 1/2" | __ | __ | __ | __ | -22° to 150° | 7 | Black | 10 | 0000000 | 0000 |
3/32" | 12" | 1 1/2" × 1 1/2" | __ | __ | __ | __ | -22° to 150° | 7 | Black | 10 | 00000000 | 0000 |
Loop × Eye | ||||||||||||
3/32" | 6" | 1 1/2" | __ | 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 10 | 00000000 | 0000 |
3/32" | 8" | 1 1/2" | __ | 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 10 | 00000000 | 0000 |
3/32" | 10" | 2" | __ | 3/16" | 9/64" | No. 10 | -22° to 150° | 7 | Black | 10 | 0000000 | 0000 |
3/32" | 12" | 1 1/2" | __ | 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 10 | 00000000 | 0000 |
2.5mm | 150mm | 42mm | 42mm | 4.2mm × 4.2mm | 1.9mm | M4 | -4° to 175° | 22 | Gray | 1 | 00000000 | 0000 |
2.5mm | 250mm | 42mm | 42mm | 4.2mm × 4.2mm | 1.9mm | M4 | -4° to 175° | 22 | Gray | 1 | 000000000 | 0000 |
Eye × Eye | ||||||||||||
3/32" | 6" | __ | __ | 17/64" × 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 25 | 00000000 | 00000 |
3/32" | 8" | __ | __ | 17/64" × 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 25 | 00000000 | 00000 |
3/32" | 10" | __ | __ | 1/4" × 1/4" | 9/64" | 1/4" | -22° to 150° | 7 | Black | 25 | 0000000 | 00000 |
3/32" | 12" | __ | __ | 17/64" × 17/64" | 9/64" | No. 16 | -22° to 150° | 7 | Black | 25 | 00000000 | 00000 |
Shock-Absorbing Fall-Arrest Lanyards with Anchor Point


For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.
Wraparound lanyards loop around a rated structure such as an I-beam and then attach to themselves to create an anchor point.
Harness End Connection | Anchor End Connection | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg., ft. | Lg. After Fall, ft. | Capacity, lbs. | Material | Construction | Type | Material | Type | Material | Snap Hook Opening Size | Specifications Met | Each | |
Wraparound Single Leg | ||||||||||||
4 to 6 | 10 1/2 | 310 | Nylon | Webbing | Snap Hook | Steel | Snap Hook | Steel | 3/4" | ANSI Z359.1 | 0000000 | 0000000 |
Shock-Absorbing Fall-Arrest Lanyards




For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.
Dual-leg lanyards attach to two anchors at once.
Harness End Connection | Anchor End Connection | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg., ft. | Lg. After Fall, ft. | Capacity, lbs. | Material | Construction | Type | Material | Type | Material | Snap Hook Opening Size | Specifications Met | Each | |
Single Leg | ||||||||||||
6 | 9 1/2 | 310 | Nylon | Webbing | Snap Hook | Steel | Snap Hook | Steel | 3/4" | ANSI Z359.1 | 0000000 | 000000 |
4 to 6 ft. | 10 1/2 | 310 | Nylon | Webbing | Snap Hook | Steel | Snap Hook | Steel | 3/4" | ANSI Z359.1 | 0000000 | 00000 |
Dual Leg | ||||||||||||
6 | 9 1/2 | 310 | Nylon | Webbing | Snap Hook | Steel | Snap Hook/Snap Hook | Steel | 3/4" | ANSI Z359.1 | 0000000 | 000000 |
4 to 6 ft. | 10 1/2 | 310 | Nylon | Webbing | Snap Hook | Steel | Snap Hook/Snap Hook | Steel | 3/4" | ANSI Z359.1 | 0000000 | 00000 |
Quick-Stop Fall-Arrest Lanyards


A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance as it will stop your fall within a few inches. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.
Harness End Connection | Anchor End Connection | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg., ft. | Capacity, lbs. | Material | Construction | Type | Material | Type | Material | Snap Hook Opening Size | Housing Material | Specifications Met | Each | |
Single Leg | ||||||||||||
20 | 420 | Nylon | Webbing | Swivel Eye | Steel | Snap Hook | Steel | 3/4" | Plastic | ANSI Z359.14 | 0000000 | 0000000 |
Tool Lanyards




Keep your equipment close and prevent accidental drops.
For No. of Tools | Connection Type | Capacity, lbs. | Lg. | Material | Construction | For Min. Tool Opening | Carabiner Material | Specifications Met | Each | |
1 | Carabiner × Elastic Loop | 10 | 35" | Nylon | Webbing | 3/8" | Aluminum | __ | 0000000 | 000000 |
1 | Carabiner × Elastic Loop | 15 | 33" | Nylon | Webbing | 1/4" | Aluminum | ANSI/ISEA 121 | 0000000 | 00000 |
1 | Carabiner × Detachable Elastic Loop | 5 | 38" | Nylon | Webbing | 3/8" | Aluminum | __ | 0000000 | 00000 |
1 | Carabiner × Carabiner | 10 | 35" | Nylon | Webbing | 1/4" | Aluminum | __ | 0000000 | 00000 |
2 | Carabiner × Carabiner × Carabiner | 15 | 35" | Nylon | Webbing | 1/4" | Stainless Steel | __ | 0000000 | 00000 |
Replacement Detachable Elastic Loop | 0000000 | Each | 00000 |
Starter Pull Cords

Replace broken or worn pull cords on machinery and tools, including those on lawn mowers.
For technical drawings and 3-D models, click on a part number.
Handle | 6 1/2 ft. | ||||||
---|---|---|---|---|---|---|---|
Rope Dia. | Material | Ht. | Wd. | Dp. | Color | Each | |
Twisted Nylon Plastic with Wire Rope Core | |||||||
1/8" | Plastic | 2 1/2" | 2 1/2" | 3/4" | Black | 0000000 | 00000 |
Pole Climbing Equipment

Scale wooden poles to perform inspections and maintenance.
Climbing belts work in conjunction with positioning straps to provide a leverage point for climbing. Attach the positioning strap and your fall-arrest lanyard to the metal D-rings on the belt. Belts are fixed, so they do not allow side-to-side movement of the D-rings. Belts also hold your tools while climbing. They have a glove-bag ring, a tape holder, a two-way knife snap, four suspender rings, and four tool loops. To find your trade size, measure from one hip bone around the back to the other hip bone, then add 2". For example, if the length you measure is 20", then your trade size is 22D.
Positioning straps wrap around the pole to provide support while at height, freeing both hands for work. Connect them to the D-rings on your climbing belt with the locking snap hooks. They adjust up to 2 feet in length.
Replacement climber pads cannot be sold to Canada due to import regulations.
Note: Pole climbing equipment is not a substitute for fall-arrest equipment. Always use pole climbing equipment in conjunction with a fall-arrest harness, lanyard, and anchor point.


Climbing Belt Trade Size | Material | Specifications Met | Features | Each | |
22D | Nylon Fabric | ASTM F887, CSA Z259.1, OSHA Compliant 29 CFR 1910.269, OSHA Compliant 29 CFR 1926.959 | Tool Holder | 0000000 | 0000000 |
23D | Nylon Fabric | ASTM F887, CSA Z259.1, OSHA Compliant 29 CFR 1910.269, OSHA Compliant 29 CFR 1926.959 | Tool Holder | 0000000 | 000000 |
24D | Nylon Fabric | ASTM F887, CSA Z259.1, OSHA Compliant 29 CFR 1910.269, OSHA Compliant 29 CFR 1926.959 | Tool Holder | 0000000 | 000000 |
26D | Nylon Fabric | ASTM F887, CSA Z259.1, OSHA Compliant 29 CFR 1910.269, OSHA Compliant 29 CFR 1926.959 | Tool Holder | 0000000 | 000000 |

Lg., ft. | Wd. | Material | Each | |
4-6 | 1 3/4" | Nylon Fabric | 0000000 | 0000000 |