These dispensers have an opening for filling without removing the nozzle.

A needle dispensing tip provides fine control for lubricating small parts.

Deliver a mist of oil using shop air.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

Serve multiple lubrication points from a single location.

Control the flow of oil to a single lubrication point.

Lubricate strips of sheet stock, wire, or sheet stock edges. Max. width is 4".

Flip the lever to start and stop flow.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Mount these directly to your machine—the cup allows oil to gradually pass through to equipment, reducing time spent on manual lubrication.

Deliver an equal amount of oil to multiple lubrication points at once.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

These manual dispensers are more portable than air-powered dispensers.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

Dispense from grease guns into grease fittings and bare lubrication points.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Sets include dispensing tips for grease fittings and bare lubrication points.

Convert dispensing tips with male threads into quick-disconnect couplings.

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.

These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.

Dispense grease with the highest-pressure-rated gun we offer.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Turn a small tube of grease into a dispenser.

Dispense small amounts of grease with this compact gun.

Deliver small amounts of grease with only a light push against the lubrication point.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Use compressed air to dispense grease.

Mount these pumps to your grease container to bulk load guns.

Dispense grease using compressed air.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Move grease-dispensing guns in any direction without kinking the outlet hose.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

Don’t wait for grease to travel through a new service line—install this grease-filled tubing between the pump and a lubrication point to begin lubricating immediately.

Lubricate single- and double-strand roller chain.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Tighten the cover to dispense grease.

Draw coolant from your existing tank.

Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.

Draw coolant from your existing tank.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Use with Snap-Loc hose to assemble and disassemble components.

Swivel the ball-socket connections to position these arms and then lock them in place.

Use with Loc-Line hose to assemble and disassemble components.

Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.

This hose is made of steel.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Install these fittings into threaded holes.

Lubricate multiple points from a single location.

Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease.

Keep standard grease fittings free of dirt and moisture.

Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery.

Access difficult-to-reach lubrication points from up to 10 ft. away.

Use these fittings in tight spaces where protruding fittings won't work.

Remove worn fittings and repair threaded holes.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.