We will reply to your message within an hour.
More
Also known as Oilite® bearings.
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.
With extra iron and filled with oil containing slippery PTFE, these bearings support heavy loads that frequently start and stop along shafts.
Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels.
The oil in these bearings is suitable for incidental contact with food.
Embedded with oil that is safe for incidental contact with food, these bearings are suitable for use in high-load applications such as bottling and filling lines in food processing plants. They are also known as Super Oilite® bearings.
With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications.
Support heavy loads that are often found in bottling and filling lines in food plants—these bearings contain extra iron and FDA-compliant oil. They’re flanged, so they handle loads both parallel and perpendicular to the shaft.
These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.
The oil in these bearings is NSF registered H1 and FDA compliant for incidental contact with food.
Made of 863 iron-copper and embedded with NSF registered H1 oil, these bearings can tackle high-load applications in food plants, such as bottling and filling lines.
With a flexible layer of neoprene sandwiched between an oil-embedded bronze bearing and rigid steel shell, these bearings reduce wear and machinery noise.
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.
A strong steel housing allows these bearings to handle higher speeds than standard oil-embedded mounted sleeve bearings.
Use these corrosion-resistant fittings in a low-pressure pipe line.
The male threads on these fittings have a sealant applied for extra leak protection.
Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.
Use these fittings in extreme-pressure conditions up to 15,000 psi.
When space is at a premium choose these compact fittings.
Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.
Use these fittings in low-pressure flow applications. They have good corrosion resistance.
The male threads on these brass fittings have a sealant applied for extra protection against leaks. Also known as Pressure Class 125 fittings, they are built for use in low-pressure applications.
Used in low-pressure pipe lines, these brass fittings have a plating that makes them shiny and improves corrosion resistance.
These brass fittings have the strength to handle high-pressure applications.
Not only do these brass fittings have the strength to handle high-pressure applications, the male threads have a sealant applied for extra protection against leaks.
The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.
Extreme pressures are no problem for these heavy-duty brass fittings.
Also known as instrumentation fittings, these have the most precise threads and the tightest tolerances of all the brass pipe fittings we offer.
Plated with nickel, these brass fittings resist rust better than steel and unfinished brass fittings. Select them when you need more strength in corrosive environments to handle higher pressures than our low-pressure fittings.
Use these fittings for low-pressure applications in noncorrosive environments.
Suitable for use in fire-protection applications, these pipe fittings are made of cast iron, so they are brittle and can be quickly opened with the strike of a sledge hammer.
The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.
These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.
A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.
Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.
In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.
Their small size makes these miniature fittings a good choice for cramped, confined spaces.
Designed for medium-pressure applications, these fittings have better strength than our low-pressure aluminum pipe fittings.
Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.
Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.
Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.
In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.
The addition of MDS gives these tubes exceptional wear resistance along with a self-lubricating surface. They're made of cast nylon 6, making them easier to machine and better electrical insulators than other MDS-filled nylon tubes.
A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.
This extruded acrylic offers similar performance as cast acrylic at a lower cost.