Connect a tube fitting and tubing to the dispenser outlet to access hard-to-reach lubrication points.

Serve multiple lubrication points from a single location.

Serve multiple lubrication points from a single location.

Flip the lever to start and stop flow.

Manually adjust the flow of oil to a single lubrication point.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Mount these directly to your machine—the cup allows oil to gradually pass through to equipment, reducing time spent on manual lubrication.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Dispense a fixed amount of oil by pumping the handle.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

These dispensers have an opening for filling without removing the nozzle.

Clamp this applicator around control cables to lubricate them with minimal mess.

A needle dispensing tip provides fine control for lubricating small parts.

Add faucets to oil dispensing stations for increased utility.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Dispense grease with the highest-pressure-rated gun we offer.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Dispense small amounts of grease with this compact gun.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

This gun comes filled with 2 oz. of lithium-thickened grease.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Use compressed air to dispense grease.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Mount these pumps to your grease container to bulk load guns.

Convert dispensing tips with male threads into quick-disconnect couplings.

Dispense from grease guns into grease fittings and bare lubrication points.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Mount holders in convenient locations to keep grease guns within reach.

These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Tighten the cover to dispense grease.

Spring pressure ensures a constant flow of grease.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease.

Useful in remote areas without access to air or electrical power.

Dispense grease using compressed air.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Move grease-dispensing guns in any direction without kinking the outlet hose.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

These dispensers have a reservoir and controls for coolant flow.

Draw coolant from your existing tank.

Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.

Kits contain lengths of hose, nozzles, valves, and caps.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

A filter/lubricator ensures efficiency and reduces wear on the pump. Often used with hydraulic oil and motor oil in addition to acidic and alkaline liquids, these pumps have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

Since these pumps move liquid by pressurizing your drum, they have few moving parts prone to wear and tear.

Use these pumps with fuel and flammable liquids, such as acetone, ethanol, and gasoline. They handle nearly twice the amount of pressure as other air-powered drum pumps to move high-viscosity liquids.

The foot pedal allows hands-free operation.

Fill air-atomizing sprayers with these pitchers. The nozzle is designed to fit into the sprayer opening and has a removable brass filter to strain out foreign particles.

Choose from a variety of containers, lids, and accessories to design a dispenser that will pour or pump contents without allowing contaminants inside. These dispensers are often used with oil and other lubricating fluids.

Even when turned upside down, these containers keep fluids inside. They include an applicator brush and a plug to seal the container.

All of these pumps have bonding and grounding wires, while some also have an internal flame arrester, to pump fuel, cleaning solvents, and lacquer thinners.

A 316 stainless steel housing makes these pumps resistant to coolants such as ethylene glycol.

For low-effort dispensing, these pumps have a lever handle that maximizes output with each stroke. Use them to pump lubricating oil, such as motor oil.

Remove liquid from hard-to-reach areas with a long, flexible intake tube that extends into deep and hard-to-access tanks.

Use these pumps to move lubricating oil, such as hydraulic and motor oil.

Rotate the handle to dispense a continuous flow of liquid.

Since these pumps use suction to draw liquid out of your container, they continue dispensing once you get them started.

These pumps have a discharge hose for transfer applications and a vacuum breaker that drains the hose to prevent siphoning. A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

Drive these fittings into unthreaded holes. They're also known as hydraulic grease fittings.

Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease.

Keep standard grease fittings free of dirt and moisture.

Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery.

Access difficult-to-reach lubrication points from up to 10 ft. away.

Use these fittings in tight spaces where protruding fittings won't work.

Remove worn fittings and repair threaded holes.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.