Apply directly to seals and O-rings to extend service life by preventing drying and cracking.

NLGI viscosity grade is a rating of a grease's consistency. NLGI 1 is about the consistency of tomato paste. NLGI 2 is about the consistency of peanut butter.

Mineral-oil-based grease, derived from petroleum, is more economical than synthetic-oil-based grease. Synthetic-oil-based grease lasts longer than mineral-oil-based grease and withstands a wider range of temperatures.

Grease with lithium thickener offers good heat and moisture resistance. Grease with PTFE thickener has good heat, moisture, and oxidation resistance. Grease with silica thickener resists washing off and reduces corrosion in wet environments. Grease with barium thickener is for use with silicone rubber O-rings and seals in open systems.

Grease with PTFE has small particles of PTFE that reduce friction and help the grease maintain its lubricity. Grease with zinc neutralizes acid and is a good replacement for leaded grease.

Grease lubricates most efficiently within the listed temperature range. Melting temperature is the point at which grease will fail and run out of equipment, leaving it to run dry.

Loctite® Krytox™ RFE PFPE LB 8209 handles extreme temperature swings, resists acids, bases, and fuels, and is long lasting. It can be used under high loads.

Jet-Lube Ezy-Open is a grease-like liquid that contains detergent and PTFE additives to clean more effectively than grease while it lubricates. Since it is a liquid, it does not have a NLGI viscosity grade, but is less viscous than anything else in our offering.

A firm consistency and resistance to evaporation make this grease ideal for vacuum applications, such as flow meters, vacuum and pressure systems, and laboratory equipment. Apply directly to seals and O-rings to prevent drying and cracking.

NLGI viscosity grade is a rating of a grease's consistency. NLGI 3 is about the consistency of vegetable shortening and is comparable to Fomblin grease. NLGI 4 is about the consistency of frozen yogurt.

Grease with PTFE thickener resists aggressive acids, bases, and solvents.

Grease lubricates most efficiently below the maximum temperature. Melting temperature is the point at which grease will fail and run out of equipment, leaving it to run dry. Nonmelting grease can be used at temperatures above the maximum temperature briefly, but then will break down more quickly.

Fluorocarbon and fluorinated polymer thickeners add chemical resistance to this grease. It remains intact when exposed to water and most solvents and chemicals. Apply directly to plastic and rubber seals and O-rings to prevent drying and cracking.

NLGI viscosity grade is a rating of a grease's consistency. NLGI 2 is about the consistency of peanut butter. NLGI 3 is about the consistency of vegetable shortening.

Grease with moly (molybdenum disulfide) has excellent resistance to wear and can withstand high-load and high-pressure applications. Grease with PTFE has small particles of PTFE that reduce friction and help the grease maintain its lubricity. It’s not for use with ketones, such as acetone and MEK.

Grease lubricates most efficiently within the listed temperature range. Melting temperature is the point at which grease will fail and run out of equipment, leaving it to run dry.

Thickened with silica, this heavy grease clings to parts so it won't wash off in wet environments. Apply directly to plastic and rubber seals and O-rings to prevent drying and cracking.

NLGI viscosity grade is a rating of a grease's consistency. NLGI 3 is about the consistency of vegetable shortening.

Grease lubricates most efficiently within the listed temperature range.

This thin grease goes on as a film to form a seal in glass and metal stop cocks. It won't react with laboratory chemicals, such as hydrochloric acid, sulfuric acid, potassium hydroxide, and salt solutions.

Grease lubricates most efficiently below the maximum temperature. Melting temperature is the point at which grease will fail and run out of equipment, leaving it to run dry.

For use in food-processing and preparation areas, these lubricants are rated for incidental food contact. Coat tight-fitting parts with them before sliding together to make assembly easier.

Mineral-oil-based lubricants have a high load-carrying capacity and can lubricate sliding loads at low-to-medium speeds.