Switch your device on and off without needing a separate switch. These connectors work with industry standard cords often found on power supplies, appliances, and other electronic devices. Wire these connectors using the quick-disconnect terminals. They slide together with mating terminals for a secure hold that's also easy to pull apart to make repairs. The terminals are on the back of the connector, so the wiring stays inside your device.

Class I shock protection means they have insulation and a protective ground. They meet UL 94 V-0, so they self-extinguish within 10 seconds if they catch fire and won’t spread the fire by dripping. They’re also UL and C-UL recognized components, CE and ENEC marked, and CSA certified—they meet U.S., Canadian, and European safety standards.

Drill mounting holes in your device to mount screw-on connectors to housings of any thickness. Snap-in connectors secure with tabs. They do not require fasteners, but they do need a specific panel thickness on your device housing and a precisely cut hole for secure mounting.

The power switch on connectors with an indicator light illuminates when your device is on.

Shielded connectors protect against interference from nearby equipment.

Connectors for 20 mm-long fuses have a drawer to hold a fuse (sold separately), which prevents short circuits and circuit overloads from damaging your device.

Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch. Wire these connectors using the quick-disconnect terminals; they slide together with matching terminals on your wiring for a secure hold that's also easy to pull apart to make repairs. The terminals are on the back of the connector, so the wiring stays inside your device.

To protect your devices, these connectors have a thermal circuit breaker that uses the excess heat when there’s overcurrent to trip the breaker and cut power. If there’s a short circuit, the breakers can safely stop up to a 2,000-Amp breakthrough current. These connectors also have Class I shock protection, so they’re insulated and have a protective ground.

These connectors meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. They’re also UL and C-UL recognized components, and CE and ENEC marked, so they meet stringent safety standards.

Distribute power from one electronic device to several others with these connectors. By housing multiple outlets in a single unit, they save space and time spent on installation. They’re compatible with IEC power cords, which are the industry standard for power connections. The outlets are C13 receptacles, also known as Sheet F outlets.

Wire these connectors into your device with the terminals on the back of each outlet. They mount to your device with snap-in tabs—no fasteners needed—but require a specific panel thickness and a precisely cut hole for secure mounting.

All meet international standards for safety. They are rated for Class I Shock Protection, meaning they have insulation and a protective ground.

Solder connections are more secure than quick-disconnect terminals. These connectors meet UL 94 V-2, which means they’ll self-extinguish within 30 seconds if they catch fire, but may drip flaming particles.

Quick-disconnect terminals are faster to wire than solder connections. The terminals slide together with the quick-disconnect terminals on your wiring and are easily disconnected by hand, but still provide a strong hold. Rated IP30, these connectors prevent objects larger than 2.5 mm, such as screwdrivers, from making contact with a live circuit and shocking you. They also meet UL 94 V-0, so they’ll self-extinguish within 10 seconds if they catch fire and won’t spread flames from dripping.

Send power to your device using the inlet, then route power to another device through the outlet—all with standard IEC power cords. Compared to using separate receptacles, these combination connectors are quicker to install and have a more streamlined appearance. Snap the connector into your panel—tabs on the side hold them in place without needing fasteners. Then solder your power supply to the wire terminals for a secure, permanent bond. C13 receptacles are also known as Sheet F outlets.

Rated IP30, these connectors prevent objects greater than 2.5mm wide, such as screwdrivers, from touching internal components and accidentally shocking you. With Class I shock protection, they’re insulated and have a protective ground.

These connectors meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. They’re also UL recognized, CE marked, CSA certified, and ENEC marked, so you know they meet stringent safety standards.

With a built-in switch, these connectors run power to appliances, power supplies, and other electronic devices while also filtering damaging EMI (electromagnetic interference). Instead of hardwiring your devices, add these connectors and plug in a standard IEC power cord. Wire these connectors using the quick-disconnect terminals; they slide together with matching terminals on your wiring for a secure hold that's also easy to pull apart to make repairs. The terminals are on the back of the connector, so the wiring stays inside your device. For the best EMI filtering performance, choose a connector with a current rating at or slightly above your device's current requirements.

Rated IP40, these connectors prevent objects larger than a 1 mm-wd. wire from touching internal components and accidentally shocking you. With Class I shock protection, they’re insulated and have a protective ground. Some have a fuse drawer to hold a fuse, which prevents short circuits and circuit overloads from damaging your device. The fuses are sold separately.

These connectors meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. They’re also UL and C-UL recognized components, ENEC marked, and CSA certified, so they meet stringent safety standards.

Screw-on connectors mount to housings of any thickness, as long as you can drill mounting holes into them. Snap-in connectors have tabs on the side to mount to housings without using fasteners. But, they require a specific panel thickness and precisely cut hole for secure mounting.

Shielded connectors protect against interference from nearby equipment.

Bring power into electronic devices while protecting them from harmful electromagnetic interference (EMI). All of these connectors are compatible with standard IEC power cords. Often used to convey power from wall outlets, there’s no need to wire your devices to an external power source. Instead, wire these connectors into your device with the terminals on the back of each connector. When selecting a connector, make sure the current is at or slightly above the requirements of your device for the best EMI filtering performance.

All of these connectors meet U.S. and international standards for safety. They also meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. Rated IP40, these connectors prevent objects larger than 1 mm, such as wire, from making contact with a live circuit and shocking you. They also include shock protection. Class I shock protection means they're insulated and have a protective ground to prevent electrical shocks.

Screw-on connectors mount to devices with any panel thickness, as long as you can drill mounting holes into the device. Snap-in connectors mount to devices with snap-in tabs—no fasteners needed—but require a specific panel thickness and a precisely cut hole for secure mounting.

Quick-disconnect terminal wire connections are faster to wire than tab terminal connections. The terminals slide together with the quick-disconnect terminals on your wiring and are easily disconnected by hand, but still provide a strong hold.

Power ancillary devices, such as chargers for electronics, from a vehicle. When used together, the plug and socket create a moisture-resistant seal. Used separately, they are compatible with devices that have standard 12-volt plugs and sockets. All have a moisture-proof, corrosion-resistant housing.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors. A threaded housing securely mates with other mini connectors and won’t come loose from shaking or vibration. They have a standard pole layout and housing thread size to reduce the chance you’ll mis-mate connectors.

Receptacles thread into panels and walls, so they work well in stationary or permanent installations. Receptacles with epoxy-coated zinc housing resist corrosion and weld-slag for use in harsh environments.

When mated, these connectors meet IP or NEMA ratings. IP67 rated connectors protect against dust and temporary submersion.

Caps protect connectors and maintain their IP and NEMA ratings when not in use.

Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining. These mini connectors have a stainless steel housing or TPE cable that resists abrasion and cracking from exposure to water, chemicals, oil, coolant, or weld slag. They’re commonly used to send power and signal to automated systems, motors, and pumps. A threaded housing securely mates with other mini connectors to keep out contaminants and won’t come loose from shaking or vibration. They have a standard pole layout and housing thread size to reduce the chance you’ll mis-mate connectors.

When mated, these connectors meet IP67 and NEMA 6P for protection against dust, submersion, washdowns, and weather.

Receptacles thread into panels and walls, so they work well in stationary or permanent installations.

Caps protect connectors and maintain their IP and NEMA ratings when not in use.

Use these connectors with servomotor, servocontrollers, and servodrives in automated equipment and assembly lines. Rated NEMA 4X, IP67, and IP69K, they resist corrosion and protect against high-pressure, high-temperature washdowns. When mating connectors, the gender, housing thread location, and pole layout must be opposite. Poles are numbered on the face of the connector.

Signal connectors communicate between servocontrollers, servodrives, and servomotors.

Power computers, lab equipment, and office machines that have IEC connections. These outlet strips have a circuit breaker to prevent damage from current overload and short circuits. Connect an IEC C13 power cord (not included) to the plug on the end to power these outlet strips.