These scales are 10 times more accurate than our other bench-top scales.

The attached cover protects the scale while you carry it.

Small enough to carry with you for measurements on the go.

For corrosion resistance in addition to portability, this scale has a powder-coated steel housing and platform.

These scales are often used on small bench tops where larger scales won’t fit.

Weigh small quantities of lightweight materials.

IP rated for washdowns and use in dusty and wet environments, these scales are NTEP approved to weigh materials that are sold by weight.

Count parts and weigh materials sold by weight.

Count and weigh loads that are difficult to lift.

Roll this scale wherever you need to weigh.

To quickly check inventory, roll these dollies wherever you need them to weigh and count the contents of drums. Their built-in scale measures weight and has an accurate piece-count mode—even while adding or removing contents from your drum.

Measure a person’s weight and height.

Determine the approximate weight of large, bulky materials that are impractical to weigh with a floor scale. These scales are often used in loading vehicles and can be suspended from a crane, block and tackle lift, A-frame, or forklift blade.

NTEP-approved, these hanging scales are for use with materials sold by weight.

Often used to weigh materials sold by weight in harsh conditions, these NTEP-approved scales have an aluminum enclosure that meets IP65 and NEMA 4 for protection from dirt and washdowns.

Housing is brass.

These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.

Measure tension force as well as weight.

Press the side of the gauge tip against an object to record the amount of tension required to move it.

Apply your load directly to the top of these gauges to measure compression force.

Measure tension force as well as weight. Also known as dynamometers.

Hold fine wire and filament.

A chuck-style grip with a round opening gets a secure hold on pins.

Mount these sensors between a robot arm and a tool for precise control during delicate tasks, such as sanding or assembling small parts.

Finger-tighten the three-jaw chuck onto the tool to be measured, then twist either the gauge or tool to test.

Measure the torque output of torque wrenches, screwdrivers, and other hand tools to ensure they deliver the right amount of torque—and check your results on a digital screen.

Calibrate torque-limiting power tools such as air-powered and impact drivers.

Use these gauges with changeable sensors and square-drive sockets to display, collect, and download torque readings.

A calibration certificate traceable to NIST is included with these stainless steel rulers.

Rulers have large numbers and deeply etched graduations.

Ensure accurate measurements with these certified rulers.

A cork back prevents slipping and protects delicate surfaces.

A clear protective coating and brass endcaps add durability to these hard-maple rulers.

Ensure reliable, repeatable measurements with these rulers.

These rulers include a certificate of calibration traceable to NIST with test measurements that confirm accuracy.

Protect your ruler from scratches and wear with a TiN (titanium nitride) coating.

Permanently mount these rulers to a machine or workbench.

Rulers are narrow and just 6" long to measure in tight spaces.

Create a ruler up to 192" long by adding continuous segments.

The graduations on these rulers are half the actual length of the object you are measuring.

Measurements are printed from top to bottom for measuring heights and depths.

Use to measure heights and tank levels.

The blade locks in place when extended until you press the release lever, and a magnetic-hook tip attaches to metal surfaces to assist vertical and distance measuring.

These tape measures have a chrome-plated, impact-resistant plastic case.

Compared to standard tape measures, these are less than half the size.

Ensure accurate measurements with certified tape measures.

Slide the lock to hold the blade in place. The case is chrome-plated, impact-resistant plastic.

The case is impact-resistant plastic that's yellow for high visibility. Slide the lock to hold the blade in place.

The blade automatically locks in place when extended and stays locked until you press the release lever.

For a comfortable and secure hold, these tape measures have a narrow case with a molded rubber grip.

Attach to curved or flat steel surfaces.

At about half the size of standard diameter tape measures, these fit in your pocket.

Also known as tree tapes, wrap these tape measures around circular items to determine diameter and measure circumference without the need for calculations.

Measure distances over 35 ft.

Easily spot the brightly colored case on these tape measures around your worksite and in your toolbox.

Protect your tape measure with these leather holders.

Measure volume in gallons without calculations.

Connect continuous segments to create a ruler up to 10 ft. long.

Also known as oil-gauging tapes, use these tape measures to check the level of oil and other fluids in deep, large containers such as tanks and vats.

This digital readout system displays precise positioning on one axis. For use with machines that perform dry machining and cutting applications, such as table saws, band saws, planers, and drill presses.

Install a digital readout stop and fence system onto the setup for your miter, chop, or radial arm saw. It displays measurements on one axis, allowing you to cut pieces up to 94" with high precision.

Reach deep into small holes and slots for precise depth measurements.

Connectable extension rods allow you to measure depths.

Measure depths up to 8" using connectable extension rods.

All gauges have zero-position memory, also known as absolute (ABS) positioning, which retains the measuring position when the gauge is turned off.

These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.

Replace your try square, miter square, depth gauge, height gauge, center-point finder, and level. The blade on these squares meets Fed. Spec. GGG-R-791H, which establishes uniform standards for accuracy, graduations, and size.

Blades are for use with High-Accuracy Combination Square Heads.

Attach to High-Accuracy Combination Square Blades with the included lockbolts.

A titanium coating protects the blade against scratches and wear.

Ensure reliable, repeatable angles.

Lay out machine tables and work stations at precise right angles. This laser generates two red lines that form a 90° angle.

Also known as try squares, these are square inside and out for checking and marking angles.

Mount on any flat surface.

Measure angles with these round protractors.

Also known as bevel protractors, set bevels and measure angles with the adjustable arm.

Take precise measurements with this protractor.

Handle big jobs such as sheet metal fabricating and pipe bending with these long-arm protractors.

A dot laser extends the working distance 200 feet beyond the tool length. This tool has two digital displays that invert when turned upside down; one shows the base angle and the other shows the moveable arm angle.