These boot covers are made of PVC to hold up in wet and oily environments. A skid-resistant sole grips wet and slippery sufaces for good traction. They close with a button, and there are two holes for adjusting the fit. Order your normal boot size unless wearing over large work boots, then order one size up.

These shoe covers are made of PVC to hold up in wet and oily environments. A skid-resistant sole grips wet and slippery surfaces for good traction.

Order your normal shoe size unless wearing over large work shoes, then order one size up.

Style B provide more coverage than style A.

These lightweight covers protect boots from dirt and grime.

Polypropylene offers economical protection in environments where liquid splashes and abrasion resistance are not a concern.

Polyethylene is made of FDA listed materials, so it’s often used in food preparation. It resists light liquid splashes.

Tyvek polyethylene provides better tear and abrasion resistance than polypropylene and polyethylene. It holds up to occasional contact with nonhazardous liquids, such as water and paint spray. It is made of heat- and pressure-bonded fibers for a material that’s soft yet strong.

Kleenguard polypropylene is made of five layers of nonwoven fabric, so it is more abrasion resistant and harder to tear than Tyvek polyethylene. It holds up to occasional contact with nonhazardous liquids, such as water and paint spray. The material is antistatic, so it protects sensitive equipment from electrostatic discharge.

Latex is a thick, sturdy rubber that holds its form better than fabric and plastic boot covers. It resists liquid splashes.

12" and 13" high covers reach mid-calf. 18" high covers are knee high.

Covers with a skid-resistant sole grip wet and slippery surfaces for good traction.

These covers are lightweight and protect shoes from dirt, grime, and liquid splashes.

Use polyethylene covers around food processing plants while reducing the risk of contaminating the food. To help you comply with Hazard Analysis and Critical Control Point (HACCP) programs, these covers contain metal additives that will set off metal detectors if they—or any piece of them—fall into your line. They’re also light blue, making them easier to spot than other white or gray covers. These covers are FDA compliant for direct contact with food.

Tyvek polyethylene covers are tear and abrasion resistant. Made of heat- and pressure-bonded fibers, they’re soft yet strong. Those with a skid-resistant sole grip wet and slippery surfaces for good traction.

Kleenguard polypropylene covers have five layers of nonwoven fabric, so they’re more abrasion resistant and harder to tear than Tyvek polyethylene covers. They’re also antistatic, so they protect sensitive equipment from electrostatic discharge.

Comformax/polyester blend covers are made of a specially treated wood pulp and fabric blend material that repels liquids, including blood and other bodily fluids. They resist tearing and offer some breathability.

Step into the dispenser and this plastic film clings to the bottom of your shoes and boots, so you don’t track dirt into your home or worksite. As you pull your foot out, cut the film from its roll on the serrated blade like you would with regular plastic wrap—you never touch any part with your hands, or even bend down. For moving the dispenser safely, the blade is retractable. These plastic film covers are durable enough that they won’t tear easily when you walk, but thin enough to apply multiple layers if you need extra protection or to cover film that’s dirty. Use them with any shoe size.

One roll of 1-mil. thick plastic film and one refillable plastic dispenser are included. When you run out of film, replace it with more of the same thickness or use 2-mil. thick film for extra strength and tear resistance.

Designed to meet clean room standards, these boot covers act as a barrier between the worker and the room to prevent pollutants such as dust particles and microbes from contaminating a space. They are rated Class 100 for use in clean rooms containing fewer than 100 particles larger than 0.5 microns in each cubic foot of air space. They are knee high with an elastic top and a tie at the ankle. A skid-resistant sole grips wet and slippery surfaces for good traction.

These covers are ASTM F2413 rated and tested to 20,000 volts AC for protection against electrical hazards. They are knee high and made of water-resistant dielectric rubber with a fabric lining for easy removal. A skid-resistant sole grips wet and slippery surfaces for good traction. They have a deep-cut heel that locks onto ladder rungs or stair edges to stabilize the wearer when climbing. Tighten the top using the adjustable strap.

Order your normal boot size unless wearing over large work boots, then order one size up.

These covers are ASTM F2413 rated and tested to 20,000 volts AC for protection against electrical hazards. They are made of water-resistant dielectric rubber with a fabric lining for easy removal. A skid-resistant sole grips wet and slippery surfaces for good traction. They have a deep-cut heel that locks onto ladder rungs or stair edges to stabilize the wearer when climbing.

Order your normal shoe size unless wearing over large work shoes, then order one size up.

Keep dust and other particles on your shoes from contaminating clean rooms. These covers have an elastic band that keeps them in place once they’re on. Made of lightweight fabric, they won’t weigh you down. They’re also water resistant, so your feet stay dry in wet areas.

Polyethylene and polypropylene covers are disposable. They stretch to fit over most shoes (up to men’s size 15). To keep contaminants off of your hands, apply and remove them with Dispensers and Removers for Clean Room Shoe Covers. They’re quick, hands-free, and you don’t need to bend down to use them. Polyethylene covers are best for short-term use. For long-term wear, use polypropylene covers—they’re more durable than polyethylene. They also have a skid-resistant sole that's coated to keep you from sliding on slick floors. These covers won't generate a static charge, so they're safe to use around sensitive electronic equipment.

Reusable when laundered to clean room standards, polyester covers resist abrasion and liquid splashes. They last up to 100 washes; wash them prior to first use. These covers have adjustable snaps, so you can create a secure and comfortable fit around your shoe.

Wear these guards over shoes or boots to shield toes and feet from accidental impact. Steel and aluminum guards meet ASTM F2413 for protection against accidental impact and compression up to 75 ft.-lbs.

Order your normal shoe size. For large work shoes, order one size up. Guards with a foot strap and snaps are designed to fit over large work shoes or boots, so order your normal shoe size.

Studs dig in and hold tight on icy surfaces.

Ice grippers with heel coverage leave the front of shoes bare, so users can climb ladders safely and operate machinery without damaging the pedals. The adjustable strap secures these grippers to shoes. They have four steel studs on each foot.

Ice grippers with full shoe coverage have studs on the toe and heel to give wearers complete traction for walking.

Slip-on grippers are made of flexible rubber or plastic that stretches to fit over shoes. They have six steel studs or eight tungsten carbide studs on each foot. Grippers with tungsten carbide studs are more durable and harder to dull than those with steel studs. They also give you more stability because they have a greater number of studs. If one of the studs breaks or goes missing, there’s a replacement stud built into the upper toe area for a quick swap. To help you handle thick snow conditions, these grippers have treaded soles for extra traction. They remain elastic even in cold temperatures, so you can stretch them over shoes using their pull tabs without cracking or breaking them.

Grippers with hook and loop straps provide a snug fit over shoes or bulky boots. They have 15 steel studs on each foot to provide better traction than slip-on grippers. Studs are replaceable.

When ordering ice grippers, order your normal shoe size.

The metal spikes on the bottom of these shoe covers prevent damage to the finish of self-leveling coatings as well as your shoes. Spikes are small enough that coatings can fill in the holes they make when you walk away, so they are level when they cure. Covers fit most shoe sizes.

Safely climb up and down steel columns without a ladder or lift, keeping both hands free to weld, inspect, or connect equipment. These grippers grab onto column flanges like a vise—even on dirty or wet steel—holding and releasing with each step. Made of steel, these grippers support the full length of your foot to reduce fatigue. The strap and buckle fit most work boots up to size 12. For traction on solid ground, these grippers have rubber pads on the bottom. When used properly, grippers help you meet OSHA standards for fall protection. They must be used with a fall-arrest lanyard and harness.

Adjust the gripping jaw to fit a column flange by loosening the center bolt by hand and sliding it up or down. Tighten the bolt to lock the bracket in place.

Replacement straps meet military specifications for nylon webbing. The buckles on these straps meet ANSI and CSA safety standards for connecting components in fall-arrest systems.

Replacement sizing brackets meet military specifications for steel surface hardness.