A wraparound lens disperses light from the sides as well as the bottom to produce ambient lighting.

Also known as pendant lights, these fixtures hang from a cord.

Fit traditional fluorescent ceiling strip lights with LED lights, which use less electricity.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens.

Update standard outlet boxes in closets, hallways, and storage rooms to use LED light.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Install sockets for medium (standard household) screw-in base light bulbs.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Customize these lights to label doors or areas of a building.

With more surface area than round bay lights, these fixtures produce softer light with less glare. Use them to replace old fluorescent lights and illuminate large, open areas with high ceilings.

Brighten chemical plants, refineries, and other facilities where flammable and combustible gases, dust, or fibers may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class I, II, and III, Division 2 hazardous locations.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Safely light up chemical processing plants, mining operations, and other large areas where combustible gases and dust are present. These lights have an explosion-proof housing that contains sparks and flames, so they won’t react to nearby hazards.

Contain explosions, sparks, and flashes—the enclosure on these ceiling lights makes them safe to use in NEC Class I and II, Division 1 hazardous locations.

Illuminate harsh, wet areas, even outside in extreme weather—these lights are often used on ship building ports. Rated NEMA 4X and UL marine listed, they’re sealed against heavy rain and washdowns, and they won’t corrode from salt water or other liquids.

Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Also known as sconces, these lights are a stylish choice for ambient and accent lighting in hallways and entryways. They’re UL or ETL listed for wet locations, so you can install them outdoors—rain and humidity won’t be a problem.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Also known as wall packs, these lights mount to exterior walls and ceilings.

These lights automatically turn on when movement is detected and off when an area is unoccupied.

Hardwire these lights to a power source.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, Class II, and Zone 1.

Communicate a status at a glance by wiring these strip lights to change color when a part is malfunctioning inside your enclosure.

Brighten enclosures and small spaces like closets and drawers—no hardwiring or outlets needed. Powered by a rechargeable battery, these lights are easy to install and help save on maintenance costs.

Rated for use in damp locations, these lights withstand humidity and moisture.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

A gasket seals the enclosure of these backup lights from washdowns.

Add lighting to machinery that’s prone to vibration—these sockets lock bayonet-base bulbs in place to resist bumps and movements. They make replacing bulbs easy because you don’t have to thread the bulbs in like screw-in sockets.

Hardwire these sockets to a power source.

Turn an overhead outlet or an extension cord into a temporary light. These sockets have a two-prong plug for a quick connection.

Mount these fans on flat ceilings. All include a support cable or downrods to mount them into joists.

Highlight small, specific areas with intensely bright light to help your machine vision camera home in on the details of your product.

The most versatile of our machine vision lights, these bar lights can be used alone, installed side-by-side, or assembled into a ring light.

In addition to being more energy-efficient than magnetic ballasts, these are lighter and quieter.