Blocks hold an adhesive-back sanding roll—cut off worn abrasive and pull out more as needed.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Choose from flat and grooved liners.

Pads are marked with inch and centimeter grid lines to guide your cut.

Place these plastic pads under the material you're punching to protect work surfaces and keep punch edges sharp.

Made of fiber-reinforced PVC, these pads endure exposure to corrosive chemicals, such as cleaning solvents, chlorine, and hydrochloric acid.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

Use these in place of normal washers to damp vibration and cushion your joint.

Ribbed grommets are more flexible than our smooth vibration-damping grommets, so they're easier to install.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Designed to mount at the point of contact between a door handle and the wall, these stops prevent handles from damaging walls when doors swing open.

For quick and easy installation, wrap these bumpers around tubing, rods, machinery legs, control shafts, and levers to protect them from impact, dents, and scratches. They're also good for providing protection during shipment and storage.

The raised bulb adds cushioning to absorb more impact than other surface guards to protect walls and other flat surfaces from impact.

With a raised bulb to absorb greater impact than standard corner guards, these guards protect walls, cabinets, and other surfaces.

The guards in this system have a metal core for added strength and stability. Combine corner guards and surface guards to create a system that protects walls and equipment from impact and wear. Often used in warehouse and manufacturing areas, these systems protect against damage from carts and vehicles.

With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

This trim has a metal core for added strength and stability. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact.

This trim is suitable for use in food preparation and processing environments. It's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact in food processing applications.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

Use this film on metal and plastic parts, appliances, and electronic equipment for protection against damage during packaging, shipping, and installation.

Often used to protect sheet metal during fiber and CO2 laser cutting, this film is also good for other fabrication processes such as bending, stamping, and forming. You can even leave this film on finished parts for protection against damage during shipping and storage.

Easily attach, move, and replace these magnetic wear strips on metal surfaces to minimize friction—simply press them on and peel them off as needed. Often found on conveyor systems and chutes, use these strips where friction between two parts or materials is wearing down equipment to extend equipment life.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

Scrub out kettles, fryers, and other equipment without fear of contaminating food lines—these pads set off your metal detector if they fall into your line.

The two halves of this attachment have spikes to sandwich the pad and keep it from slipping off center.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Filled with carbon and graphite, this naturally slippery PTFE stands up to wear better than standard PTFE.

Just as chemical resistant as PTFE, yet FEP offers greater impact strength. Use it to make valve components and gaskets.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

These PEEK sheets can be machined to tight tolerances for use in electrical and semiconductor parts, such as test sockets.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

This film conducts electricity to prevent the buildup of static charges.

Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.

Widely used to make parts that require autoclaving, polysulfone is a hard, rigid material that’s easy to machine and thermoform. It maintains its physical properties when heated, even when exposed to steam.

Filled with glass, these Torlon 5030 bars are stronger and more rigid than Torlon 4301 and 4203, yet still electrically insulate like Torlon 4203.

When excellent chemical resistance is combined with an ability to hold tight tolerances, the result is PPS—a material that’s widely machined into parts for chemical-processing applications. It is comparable to Techtron and Ryton.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

This material suppresses static charges to prevent dust from building up.

The addition of carbon gives this material the ability to divert static electricity faster than antistatic UHMW.

Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.

Compared to our standard UHMW polyethylene, these sheets and bars hold up better to scuffs and scrapes in high-speed, high-precision, and high-impact applications—such as conveyor equipment, chute liners, and machine guards. Also known as Tivar HPV.

Prolonged outdoor exposure won’t discolor or degrade VHMW.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Designed for extreme wear resistance, this Kevlar-filled nylon 6/6 material lasts up to 20 times longer than unfilled nylon. Also known as Hydlar Z, it is often used for parts that are continuously exposed to wear and abrasion, such as wear strips and bushings.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

This material prevents the buildup of static charges.

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

Also known as pipe-grade HDPE, these sheets are about four times more impact resistant than standard HDPE and hold up outdoors, and in wet environments.

Widely used in semiconductor applications, this polypropylene meets UL flame-retardance standards.

Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

A polyester string reinforcement gives this material better tear resistance than standard LDPE film.

A layer of soft LDPE is sandwiched between two thin layers of aluminum for strength and rigidity.

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Create signs and partitions with this easy to cut PVC foam.

Widely used for vehicle interiors and equipment housings, this blended material maintains its physical properties after thermoforming. It is comparable to Kydex.

This film is often used as a separator when heating parts in an oven.

These black polyester sheets protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into pump components and spacers.

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.