Coated with aluminum oxide—the most common abrasive material, hard enough to sand steel and wood.

A selection of 40 emery and crocus sanding sheets are included in these assortments.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

These assortments include three cut-to-length sanding rolls of various grits in a convenient dispenser.

The grit particles are block shaped and cut slowly.

Sanding rolls with precision-shaped ceramic alumina abrade hard metals like stainless steel faster than standard ceramic alumina rolls because of their sharp, outwardly pointed grit.

These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Assortments include three cut-to-length sanding rolls of various grits that resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents.

Keep an assortment of sheets that prevent dust and debris from building up on the abrasive surface close at hand.

A cushioned layer lets you apply more even sanding pressure on your workpiece, creating finer and more consistent finishes.

Sized for tight spaces, these small pads sand flat and curved surfaces. They have a flexible foam layer that gives you more control over sanding pressure, creating finer and more consistent finishes.

When you need to achieve a more consistent finish, choose nylon mesh sanding rolls over paper- or cloth-backed rolls.

The mesh in these sanding pads flexes to compensate for uneven pressure as you sand, producing a consistent finish.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

These sponges prevent debris from accumulating on the abrasive surface and keep operating temperatures low.

Evenly sand two surfaces at once.

Peel and stick to your sanding tool. When it’s time to change the sheet, peel it off.

Sanding rolls with precision-shaped ceramic alumina abrade hard metals like stainless steel faster than standard ceramic alumina rolls because of their sharp, outwardly pointed grit.

Cut the length you need, then quickly attach, remove, and reuse.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.

Dust and debris won't build up on the abrasive surface.

A coating prevents dust and debris from building up on the abrasive surface.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The premium abrasive stays sharp longer.

The ceramic alumina abrasive on these discs is sharp and dense enough to shape hard metals such as stainless steel, nickel, and cast iron without dulling quickly.

Coated with either ceramic alumina or a premium form of aluminum oxide, these discs last longer, cut faster, and produce a more consistent finish than standard hook and loop discs.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

Smooth or shape work surfaces. Good for general purpose sanding, the aluminum oxide abrasive on these belts is tough and won’t crack under stress.

These belts resist deterioration when used with water or cutting fluids.

Avoid clogs when you're removing paint or rust. The widely spaced grains on these belts give dust and debris a place to collect so they won't build up on the surface.

Sanding belts with precision-shaped ceramic alumina abrade hard metals like stainless steel faster than standard ceramic alumina belts because of their sharp, outwardly pointed grit.

When you need to achieve a more consistent finish, choose nylon mesh sanding belts over paper- or cloth-backed belts.

Dense and hard, the ceramic alumina abrasive on these belts removes material faster and lasts longer than standard aluminum oxide abrasives.

At least 16" wide, these sanding belts leave a smooth, consistent finish on large workpieces. They have an aluminum oxide abrasive, which is the most common abrasive for general use.

Sand inside pipes, tubes, and hard to reach corners with these pads.