The cleaning solution is stored inside a drum to reduce fumes and solvent evaporation.

Leave a corrosion-resistant film on parts after washing.

A dolly with casters makes it easy to move these parts washers around your facility.

Clean small parts with these compact washers.

These brushes have steel bristles for removing weld slag and heavy surface contamination.

Steel bristles remove weld slag and heavy surface contamination.

Precisely control the cleaning process by setting the temperature and time.

Also known as semi-aqueous cleaning solutions, these consist of water and other components such as ammonia or citrus. They clean parts with heavy contamination such as buffing and lapping compounds.

Dissolve residue that solvent-based cleaning solutions can leave behind.

These premium nozzles are engineered for the most efficient airflow consumption.

Control consumption and noise by adjusting the airflow.

The extra length allows access into hard-to-reach areas.

The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.

Adjust airflow to control consumption and noise.

The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.

Choose a base, hose, and nozzle for a custom setup.

Convert your blowgun to a spray gun. These nozzles spray air and liquids at the same time.

Blow debris and sweep it away with the built-in brush.

The lightweight plastic construction makes these blowguns more comfortable to hold than metal.

Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.

Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.

Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

The included hose is ready to connect to your air supply.

Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.

Increase your reach with the telescoping nozzle.

These blowguns provide more than two times the airflow of standard guns.

Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.

Blow air backward from the nozzle to clean out the inside of pipes, tubes, and channels without pushing debris into your system.

The most powerful blowguns we sell, these use compressed air to clean and blow debris.

Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.

Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).

Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.

Producing the same airflow as standard air knives, these are quieter and use 18% less compressed air.

Use one bracket for 3" to 18" wide air knives; two brackets for 24" to 42" wide air knives, and three brackets for 48" wide air knives.

Dry and cool parts, wipe conveyor belts, control coating depth, and blow liquid, chips, and dust off of equipment in sanitary environments.

An ionizing bar temporarily neutralizes static to protect against ESD (electrostatic discharge).

Grip the handles on these brushes for extra leverage when cleaning tubes, pipes, and holes by hand.

The handle makes it easy to clean tubes, pipes, and holes by hand.

The long shaft on these brushes snakes around curves to reach deep into tubes.

Made of phosphorus bronze that is Factory Mutual approved, these brushes inhibit sparking and are nonmagnetic and corrosion resistant.

The handle makes it easy to brush by hand. Clean delicate surfaces inside tubes, pipes, and holes.

The handle makes it easy to brush by hand. Clean delicate surfaces inside tubes, pipes, and holes.

Attach the shank to a handle or power tool.

These brushes withstand temperatures up to 500°.

Attach the shank to a handle or power tool.

Use for tasks such as removing weld slag, heavy surface contamination, and large burs from tubes, pipes, and holes.

Use for soft and hard deposits.

Abrasive grains are embedded in the entire length of the bristles to remove workpiece material as well as surface contamination in a single step.

Bristles inside the housing and a protruding brush clean the inside and outside of tubes in one step. Sets include brushes for three different tube sizes.

Clean the inside and outside of a tube with one brush.

Bristles at the top of these brushes clean the bottom of closed-end holes.

Sets include an assortment of brushes for cleaning the inside and outside of tubes.

Use for tasks such as removing weld slag, heavy surface contamination, and large burs.

Remove light-to-medium rust and stains and small burs.

Work in tiny spaces and on very small parts to remove light-to-medium rust and stains and small burs.

Use two types of bristles on one brush to remove light-to-medium rust and stains and small burs.

Work on delicate surfaces in tiny spaces and on very small parts.

The handle curves sharply for cleaning in hard-to-reach spots.

Use two types of bristles on one brush.

These brushes have a 20 1/2" long handle.

The bristles are coated with a synthetic compound that keeps them stiff and straight so they’re more aggressive and last longer than standard brushes.

Clean delicate surfaces in hard-to-reach spots. Use these brushes to remove light-to-medium rust and stains and small burs.

The bristles are coated with a synthetic compound that keeps them stiff and straight so they last longer than standard brushes.

The abrasive lasts longer than that of standard brushes.

Removable bands around the bristles keep them from flaring and breaking. Adjust the bands to change bristle length.

Remove light-to-medium rust and stains and small burs with these flexible-bristle brushes.

Use for tasks such as removing weld slag, heavy surface contamination, and large burs.

Use on delicate surfaces.

Baskets are wire mesh.

Create a basket to meet your exact size specifications.

Made of polypropylene, these baskets withstand most acids and chemicals.

Replace filters or add parts baskets and drum dollies to your parts cleaning vacuum/blowers. All of these filters and accessories can be used with compatible MiJET parts cleaners.

Clean small, narrow areas with these brushes.

Often used to clean windows and vehicles, these soft-bristled brushes won’t scratch. Their bristle block has a wrap-around bumper to protect surfaces.

Clean hard-to-reach areas in pharmaceutical and food-processing plants—these scrub brushes have metal and chemical additives that set off metal detectors and show up on an X-ray if they fall into your line.

Let your drill do the scrubbing and scouring for you.

The tips of these swabs are soaked with isopropyl alcohol.

Not only are these swabs adhesive and lint free, they also have excellent particle entrapment and the best solvent-holding ability of any swab.

These swabs dissipate static electricity and are often used for cleaning electronic components.