Caps are watertight to protect safe-break plugs when not in use.

Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.

Meet international standards IEC 309-1 and 309-2.

A current rating up to 400 amps makes these connectors suitable for use in industrial machinery and floodlights.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Simplify wiring and reduce the number of cords in your automation setup.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Block signal interference from nearby devices, such as motors and transmitters, while maintaining a strong, stable connection for M12 threads.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Reduce the number of cords needed to send and receive signals where space is tight.

Minimize signal loss between low-current devices with M8 connections.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Join two devices with M8 connectors to a single cord, distribution block, or I/O module with M12 connectors to save space and reduce the number of cords in industrial automation setups. Often used with sensors and switches, these splitters send or receive two signals through one connection.

Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. Use them with standard Molex connectors.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

Build a connector that fits in tight spaces by combining male and female inserts for power and signal with a compact base and a hood.

Often used with thermosensors or brakes on large motors, these carry more than twice the current of standard latching connectors.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

The smallest latching connectors we offer, these fit in tight spaces. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

With a PVC housing, connectors withstand exposure to chemicals, oil, fuel, and salt water.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Use these sockets with Allen-Bradley servomotor systems.

Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.

Use these connectors in vehicles and other agricultural and construction equipment. They have a sealed nylon housing that resists dust and temporary submersion.

Power robotic arms and other high-amperage machines in motor controls, conveyors, and sorting and packaging systems from your main M35 power line.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

Connect and disconnect your equipment all at once.

Reduce the number of electrical connections in sanitary areas, such as food plants—these connectors combine Ethernet, a power cable, and wire for signals into a single connection point.

Extend an audio connection by plugging a cord into each end of these adapters.

These connectors are designed for use in audio equipment.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Compatible with Molex connectors, these cords are sized to fit in tight spaces. They're often used in the interior of machines.

Like a tree trunk connecting to branches, these cords supply power to a chain of devices. Send power to high-amperage motors, robotic arms, and other machines in motor controls, conveyors, and sorting and packaging systems.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Similar to branches extending from a tree, these cords disperse power from a main power line to run a chain of devices. Power high-amperage fans, pumps, and other machines in motor controls, conveyors, and sorting and packaging systems.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

Play audio from one source on two different speakers.

Connect audio to a single speaker, or extend the distance between stereo audio devices.

Connect these lifters to your robot arm to pick up and move items using suction. They're electric, so you don't need a compressed air source.

Plug thermocouple probes into a control panel.

Also known as feedthrough connectors, these mount through threaded tank openings to make connections between thermocouple probes and external equipment.

Extend the reach of your thermocouple probe—plug-in connectors on both ends of this wire speed up installation.

Adapt 10-pin cables for connection to a USB port on a PC.