A grease fitting makes these hinges easy to lubricate.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Made of plastic with a metal additive, these hinges will set off metal detectors if a piece breaks off and falls into your line.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

These hinges with holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

To make reconnecting doors easier than other pull release quick disconnect hinges, these have a keeper that holds the pin in a retracted position.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

These hinges are made of metal.

In addition to rotating 360°, these hinges tilt up and down.

Eliminate slamming lids—these hinges hold lids open at their widest angle and then slowly pull them closed.

Only one cutout (mortise) is needed for these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

After a light push on the door, springs in these hinges swing doors and gates fully open.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

The mounting holes on these hinges form an industry-standard half-moon shape.

Bearings allow these hinges to open and close doors smoothly. The mounting holes form an industry-standard half-moon shape.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

Bearings allow these hinges to open and close doors smoothly.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability.

To reinforce loose or damaged hinges, mount one of these hinges to the top edge of the pull-side of the door.

Create precise outlines for hinge mortises (cutouts). Position the cutter on a wood door or frame and hit it with a hammer to imprint the outline.

Keep environments free of contaminants—with plastic hinge leaves and a metal pin, there's no metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

Choose these hinges for their adherence to strict military standards for material and construction.

Mounting slots allow door alignment adjustments during and after hinge installation.

When the door is closed, the distance between the leaves is larger than the pin diameter, creating an offset to accommodate a gasket or trim.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

These hinges have a standard range of motion of 100° to 120°.

Hinge leaves fit into two cutouts (mortises) to mount flush with door and frame edges.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

Easier to install than other concealed cabinet hinges, these do not require a cutout.

Slip the hinge pins into 11/32" Dia. × 5/16" Dp. holes in a cabinet.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

A spring in these hinges automatically swings doors and gates closed behind you.

These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging.

Wide hinge leaves provide a large mounting surface to keep trailer doors from sagging.

Plastic pins are a nonconductive and nonmagnetic alternative to metal dowel pins. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.

Grooves hold these pins in place, and a round head gives them a finished appearance.

These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. Also known as type G pins.

Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.

Barbs bite into plastics and soft metals such as aluminum for a strong hold, and a round head gives a finished appearance.

The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

Pass wires and other components through these hollow pins.

Made of compressed wood, these biscuits fit into slots cut into wood. When glued, they expand for a tight fit.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

Lock the nose in the retracted position by pulling the knob and rotating it 90°.

Lock the nose in the retracted position by pulling the knob and rotating it 90°.

Use hinges to add doors, lids, and machine guards to T-slotted framing.

Place one of these wire springs onto your door's hinge pin to keep it open.