Made of zinc-plated steel or stainless steel, these clevis rod ends offer more corrosion resistance than standard steel clevis rod ends.

In addition to offering superior chemical resistance, these lightweight, fiber-reinforced nylon rod ends also reduce noise and vibration.

A male-threaded shank lets you build a linkage with a tapped tube or any female-threaded connection.

Attach these nuts to rods, pipes, and tubes to make pivoting and hinge movements where misalignment is not a concern.

Keep dirt out and lubrication in to extend the life of your rod ends.

Replace access door hinges with these switches; they actuate when the door opens at least 4°.

Mount the hinge leaves to the surface of the door and the frame. These hinges are easy to install because they don't require cutouts (mortises).

Open doors past their frame to make extra room for people and large items, such as carts, furniture, and wheelchairs, to pass through.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door up or down after it's hung.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

In addition to rotating 360°, these hinges tilt up and down.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

These hinges are made of metal.

These hinges are made of metal.

A grease fitting makes these hinges easy to lubricate.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

These hinges without holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

Lock these hinges open at any angle within their range of motion.

The springs in these hinges swing doors and gates fully open after a light push on the door.

Use these hinges on lightweight screen and storm doors as well as small gates.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Also known as gravity hinges, the weight of the door returns these hinges to a closed position without the help of springs.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

The mounting holes form an industry-standard half-moon shape.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

The mounting holes on these hinges form an industry-standard half-moon shape.

A stud projects from the back of each hinge leaf to prevent the door from being forced open. The mounting holes form an industry-standard half-moon shape.

To reinforce loose or damaged hinges, mount one of these hinges to the top edge of the pull-side of the door.

Bearings allow these hinges to open and close doors smoothly.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Plastic bushings on these metal hinges prevent metal-to-metal contact that can release particles as hinges open and close.

Easier to install than other concealed cabinet hinges, these do not require a cutout.

Eliminate slamming doors—push the door and these hinges slowly pull it closed.

With a 170° range of motion, these hinges are for doors that need to open wide.

Hinge leaves fit into two cutouts (mortises) to mount flush with door and frame edges.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

To ensure a good fit, these hinges have screws for horizontal, vertical, and depth adjustments after installation.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

These hinges are made of metal.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The leaves of these hinges almost touch when the door is closed. They are often used in electrical enclosures for a tight seal.

Bearings allow these hinges to open and close doors smoothly.

A spring in these hinges automatically swings doors and gates closed behind you.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges.

These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging.

Pivots provide smooth motion at the junction between two T-slotted rails.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Hold heavy lids open with these supports.

To eliminate slamming and smashed fingers, these supports automatically pull lids shut when they approach the closed position. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Attach these fittings to the end of a ball screw jack to create pivoting connections with clevis rod ends and other linkages.

Stainless steel hubs allow these U-joints to handle harsh environments.

These joints are made of steel.

These U-joints are made of steel or zinc.

These U-joints are made of steel.

These steel U-joints meet MIL-U-20625A Class A and have hardened yoke ears for added strength and durability.

Made of stainless steel, these U-joints offer excellent corrosion resistance.

Keep shafts moving in sync with these U-joints—a flexible spring at the center stabilizes input and output speed and reduces vibration.

A set of gears transmit rotary motion at angles up to 136°—the widest angle of all our U-joints. They are for hand-powered, low-speed applications.

Customize the bore size of these joints to fit your shaft. Each end has a small centered starter hole that makes drilling easy.

These pin-and-block style U-joints work at lower speeds but transmit greater torque than needle-bearing joints.