Use these metal dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

The low-profile head on these pins holds them in place on one side.

Also known as universal clevis pins, these pins have holes on 1/4" centers so you can change the length by moving the cotter pin.

The bend makes these pins easy to insert and pull out.

Install or remove these pins from either side.

The wire retainer snaps closed to secure the pin for a one-piece alternative to a clevis and cotter pin combination. Also known as PTO pins.

Install or remove these pins from either side. Slide a retaining ring into the groove for a secure hold that takes up less space than a cotter pin.

A swivel handle makes these pins easy to install and remove, while the toggle locks them in place. Flip the toggle to release the pin.

The smooth ring handle on these pins won't catch on parts. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

A bright-orange plastic-coated handle makes these pins easy to see and easy to grip. Pins have a spring-loaded ball that pops out when the pin is pushed into a hole, and retracts when the pin is pulled out.

A T-handle makes these pins easy to grip. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

The smooth ring handle on these pins won't catch on parts. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

For a more secure hold than standard quick-release pins, these pins lock in place until you push the button to release the spring-loaded retaining balls.

The extra height and smaller width of the grip make the button more accessible in tight spaces. For a more secure hold than standard quick-release pins, these pins lock in place until you push the button to release the spring-loaded retaining balls.

The extra height and smaller width of the grip make the button more accessible in tight spaces. Made entirely of stainless steel, they stand up to corrosive enviroments. Pins lock in place until you push the button to release the spring-loaded retaining balls.

Four spring-loaded retaining balls provide extra holding power. Made entirely of stainless steel, these pins stand up to corrosive enviroments. They lock in place until you push the button to release the spring-loaded retaining balls.

Also known as double-acting pins, these pins lock in place until you push the button or pull the ring to release the spring-loaded retaining balls. The smooth ring handle won't catch on parts.

Push parts out of molds with these hardened pins. Also known as knockout and forged pins.

Also known as roll, tension, split, and expansion pins, these pins have a slot along one side that you squeeze closed to install them into unthreaded holes.

Choose a material, head type, end type, and size to create a custom pin.

Use in applications requiring high strength.

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.

These 18-8 stainless steel anchors have good chemical resistance.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

A hex head allows for a secure grip with a wrench.

Support and position workpieces and fixtures from the bottom or side. These buttons press into a drilled hole for permanent installation.

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.