Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Also known as ANSI flanges.

Also known as Code 61 SAE hydraulic flanges, these let you create an access point in a high-pressure hydraulic line.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Use these heavy duty forged flanges for high-pressure applications.

Typically used with thick-wall and high-pressure stainless steel unthreaded pipe fittings.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Also known as Class 1500 steel flanges, these have the strength to handle high pressures.

Combine an adapter with a two-piece pipe flange (sold separately) to build a customized flange connection for noncorrosive environments.

Typically used with high-pressure galvanized iron and steel threaded pipe fittings. Also known as Schedule 160.

Made to tighter tolerances than other steel pipe fittings, these are also known as instrumentation fittings.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.

Also known as Code 61 SAE hydraulic flanges.

Also known as Class 6000 fittings, these heavy duty forged fittings are the strongest steel fittings we offer.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

Designed for ultra-clean environments, these manifolds are cleaned, dried, and vacuum sealed in plastic to prevent dirt and moisture from contaminating the inside. Use them to distribute air or fluid to multiple locations from a single supply source. Also known as headers.

Mount these manifolds on the end of a hose line to distribute air, water, or hydraulic fluid to three locations from a single supply source.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

The sleeve in these fittings is rubber instead of metal, so it cushions the tubing and absorbs vibration while creating a tight seal.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Instead of a metal sleeve (ferrule), these fittings have a rubber sleeve that cushions tubing and absorbs vibration to maintain a tight seal, even when connected to large pumps.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Also known as JIS (Japanese Industrial Standard) fittings.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

With the best corrosion resistance of any metal fitting we offer, these Hastelloy fittings will stand up to aggressive chemicals and are resistant to pitting and stress cracking. Also known as instrumentation fittings, they include a nut with two sleeves.

Couplings are metal, which has better durability than plastic cam-and-groove hose couplings. Also known as dry disconnects and double shut-off couplings, they have a shut-off valve in the plug and the socket for minimal fluid loss when disconnecting your hose line.

Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 6,000 psi

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Use these couplings at pressures up to 10,000 psi. The plug and socket thread together to form a stronger connection than other quick-disconnect couplings. They are compatible with High-Pressure Thread-Lock-shape plugs and sockets.

Use these couplings at pressures up to 7,200 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with International Standard ISO Minimal-Spill-shape plugs and sockets.

Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.