Suitable for use in fire-protection applications, these flanges are brittle and can be quickly opened with the strike of a sledge hammer. Bolt two flanges of the same size together with a gasket (sold separately) to create an access point within a line. Use in noncorrosive environments.

For technical drawings and 3-D models, click on a part number.

The galvanized finish on these flanges provides fair corrosion resistance. Also known as Class 150 flanges, they are for use in low-pressure applications. Bolt two same-size flanges together with a gasket (sold separately) to create an access point within a line.

For technical drawings and 3-D models, click on a part number.

With better strength than our low-pressure steel flanges, these are for use in medium-pressure applications. Bolt two same-size flanges together with a gasket (sold separately) to create an access point within a line. Flanges are also known as Class 300 or Class 600 flanges. Use in noncorrosive environments.

For technical drawings and 3-D models, click on a part number.

Bolt two flat-surface flanges or two raised-surface flanges of the same size together with a gasket (sold separately) to create an access point in a pipe line. Flanges are for use with low-pressure applications in noncorrosive environments.

Butt-weld flanges are also known as weld-neck flanges; the flange neck has a beveled end that, when flush to pipe, creates a trough for a strong weld.

Slip-on weld flanges have no internal stop; slide a pipe through the flange and weld on both sides.

Socket-connect flanges have an internal stop that supports the pipe when welding and prevents the pipe from sliding all the way through.

Stub-end flanges are also known as lap-joint flanges; use them with a stub-end straight adapter (not included). The stub-end straight adapter slides into the flange and welds to pipe (not the flange). Since the flange isn’t welded to the pipe, it can be disconnected easily for frequent cleaning and inspecting.

Cap flanges are also known as blind flanges.

For technical drawings and 3-D models, click on a part number.

Forged for extra strength, these heavy duty flanges can withstand high-pressure applications. Bolt two flat-surface flanges or two raised-surface flanges of the same size together with a gasket (sold separately) to create an access point in a pipe line.

Butt-weld flanges are also known as weld-neck flanges; the flange neck has a beveled end that, when flush to pipe, creates a trough for a strong weld.

Slip-on weld flanges have no internal stop; slide a pipe through the flange and weld on both sides.

Socket-connect flanges have an internal stop that supports the pipe when welding and prevents the pipe from sliding all the way through.

Stub-end flanges are also known as lap-joint flanges; use them with a stub-end straight adapter (not included). The stub-end straight adapter slides into the flange and welds to pipe (not the flange). Since the flange isn’t welded to the pipe, it can be disconnected easily for frequent cleaning and inspecting.

Cap flanges are also known as blind flanges.

For technical drawings and 3-D models, click on a part number.

Connect these fittings to Schedule 80 pipe–they have thicker, stronger walls than standard-wall fittings so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. Fittings are plastic for good corrosion resistance. They meet ASTM D1784 specifications and testing requirements for material quality.

Fittings for drinking water meet NSF/ANSI Standard 61.

Attach socket-connect ends to unthreaded pipe or another socket-connect fitting with a PVC primer and cement (also known as solvent weld).

Note: For fittings that are not rated for pressure, you can use the pressure rating of the plastic pipe as a reference. Threaded fittings are limited to 50% of the rated pressure of the pipe.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

With thicker, stronger walls than standard-wall pipe, this Schedule 80 pipe can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. It’s made of PVC, which has good corrosion resistance. Pipe meets ASTM D1784 and ASTM D1785 specifications and testing requirements for material quality.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Also known as Class 150 flanges, these flanges have thick, strong walls to handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They meet NSF/ANSI Standard 61 for drinking water. Bolt two same-size flanges together with a gasket (sold separately) to create an access point within a line. Flanges are PVC, which has good corrosion resistance. They meet ASTM D1784 specifications and testing requirements for material quality.

Warning: Never use plastic pipe flanges and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Connect these fittings to Schedule 40 plastic pipe–they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Fittings for drinking water meet NSF/ANSI Standard 61.

Attach socket-connect ends to unthreaded pipe or another socket-connect fitting with a PVC primer and cement (also known as solvent weld).

To prevent leaks in threaded connections, apply a sealant to the male threads. For plastic threads, apply a non-hardening, plastic-compatible sealant. Tape or sealants with PTFE are not recommended for plastic-to-plastic connections. Fittings that meet ASTM D1784, ASTM D1785, and ASTM D4066 adhere to specifications and testing requirements for material quality.

Note: For fittings that are not rated for pressure, you can use the pressure rating of the plastic pipe as a reference. Threaded fittings are limited to 50% of the rated pressure of the pipe.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Connect this pipe to standard-wall plastic pipe fittings for a variety of residential and commercial low-pressure plumbing and water supply applications. It’s made of PVC, which has good corrosion resistance. Connect to unthreaded female socket-connect fittings using a PVC primer and cement (also known as solvent weld).

Pipe for drinking water meets NSF/ANSI Standard 61.

Pipe that meets ASTM D1784 and ASTM D1785 adheres to specifications and testing requirements for material quality.

Bend radius is the point to which you can bend pipe or tubing without damaging it. The smaller the measurement, the better the bend.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

These joints reduce stress, vibration, and noise in piping systems by providing a point of flexibility to absorb movement. The flanged ends rotate for easy bolt hole alignment during installation. They mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints have a flexible body that is reinforced with nylon for added strength.

For technical drawings and 3-D models, click on a part number.

These all-metal expansion joints can handle higher temperatures than rubber expansion joints. They reduce stress, vibration, and noise in piping systems by providing a point of flexibility to absorb movement. Joints are made of 304 stainless steel for very good corrosion resistance. The flanged ends rotate for easy bolt hole alignment during installation. Flanges mate with a same-size flat-surface Class 150 flange with a gasket (sold separately).

Liners (sold separately) slide into the expansion joint to provide a smooth interior for unrestricted flow.

For technical drawings and 3-D models, click on a part number.

Because the flanges are molded into the body for a wide sealing surface, these joints provide a tighter seal than other expansion joints. Each flange is supported by a zinc-plated steel plate. Flanges mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints reduce stress, vibration, and noise in metal piping systems by providing a point of flexibility to absorb movement. They have a flexible body that is reinforced with cord for added strength.

For technical drawings and 3-D models, click on a part number.

These expansion joints have a double-bulb design for extra movement and vibration absorption. The flanged ends rotate for easy bolt hole alignment during installation. They mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints have a flexible body that is reinforced with nylon for added strength.

For technical drawings and 3-D models, click on a part number.

Slip these joints over your pipe ends and tighten the band clamps for a secure hold. Joints have a triple-bulb design that provides excellent vibration absorption to reduce stress on your piping system. They also have reinforcing rings for extra support during pressure surges and in vacuum applications.

Neoprene rubber joints are more abrasion resistant than silicone rubber joints.

For technical drawings and 3-D models, click on a part number.

These joints weld to unthreaded pipe or another butt-weld fitting for a leak-resistant, permanent connection. They reduce stress, vibration, and noise in metal piping systems by providing a point of flexibility to absorb movement.

For technical drawings and 3-D models, click on a part number.

Low-profile barbs and a longer first barb allow for a smoother, easier installation than other barbed fittings. Slide the barbed end into rubber hose and secure with a clamp.

Steel fittings are stronger and more durable than other metal fittings. They should be used in noncorrosive environments. Zinc-plated steel fittings have slightly better corrosion resistance than unplated steel fittings. Aluminum fittings are lighter in weight than other metal fittings. They have good corrosion resistance. Fittings with a threaded end are also known as hose nipples.

For technical drawings and 3-D models, click on a part number.

Low-profile barbs and a longer first barb allow for a smoother, easier installation than other barbed fittings. Slide the barbed end into rubber hose and secure with a clamp. Fittings are 316 stainless steel, which has excellent corrosion resistance to withstand a variety of chemicals.

Adapters are also known as hose nipples; they adapt a barbed end to a threaded end.

For technical drawings and 3-D models, click on a part number.