Use these corrosion-resistant fittings in a low-pressure pipe line.

The male threads on these fittings have a sealant applied for extra leak protection.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Use these fittings for low-pressure applications in noncorrosive environments.

Pipe has clockwise (right-hand) threads on one end and counterclockwise (left-hand) threads on the other end. When you use a wrench to turn, connections on both ends tighten at the same time.

Made of galvanized steel, this Schedule 40 pipe has fair corrosion resistance and is designed for low-pressure applications.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

Typically used with medium-pressure iron and steel threaded pipe fittings. Also known as Schedule 80.

Typically used with medium-pressure galvanized iron and steel threaded pipe fittings. Also known as Schedule 80.

Made to tighter tolerances than other steel pipe fittings, these are also known as instrumentation fittings.

These brass fittings have the strength to handle high-pressure applications.

Not only do these brass fittings have the strength to handle high-pressure applications, the male threads have a sealant applied for extra protection against leaks.

Typically used with high-pressure brass and bronze threaded pipe fittings.

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

The male threads on these brass fittings have a sealant applied for extra protection against leaks. Also known as Pressure Class 125 fittings, they are built for use in low-pressure applications.

Less than an inch in length, these miniature fittings work well in low-pressure pipe lines that are tight on space.

Typically used with low-pressure brass and bronze threaded pipe fittings.

Typically used with medium-pressure brass and bronze threaded pipe fittings.

Typically used with precision extreme-pressure brass and bronze threaded pipe fittings.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Designed for medium-pressure applications, these fittings have better strength than our low-pressure aluminum pipe fittings.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications up to 200° F.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

Not only do these PFA fittings have the chemical resistance to handle acid and salt water, they also have better crack resistance than other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

Use these plastic fittings to connect gasoline fuel lines to machines and equipment. They have excellent corrosion resistance as well as high strength and impact resistance.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Joints are aluminum, which is lighter than other metals.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Instead of a metal sleeve (ferrule), these fittings have a rubber sleeve that cushions tubing and absorbs vibration to maintain a tight seal, even when connected to large pumps.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

The threads on these fittings mate with NPT, NPTF, BSPT, and BSPP threads.

Withstanding temperatures up to 300° F, these fittings have the highest temperature rating of all our push-to-connect tube fittings for air and water.

Barbs grip onto tubing.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Silver ions in the material help inhibit the growth of bacteria, mold, fungi, and other odor-causing microbes.

The nickel plating on these fittings provides better corrosion resistance than unplated brass fittings.

Color-code fittings for easy identification. These aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Fittings have good corrosion resistance.

A built-in tube support slips inside the tubing to prevent collapsing and provides a sturdy connection for an extra-tight seal.

Lighter in weight than metal quick-disconnect couplings, these couplings are plastic.

Couplings can handle pressures up to 250 psi.

These brass couplings have good corrosion resistance.

Made of plastic, these couplings are lighter in weight than metal quick-turn couplings.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

Fittings withstand temperatures up to 220° F.

Fittings have a sleeve that bites into tubing as you tighten the nut to form a seal in applications up to 120 psi. Also known as flareless fittings.

Fittings have a barb that grips onto tubing. Use in applications up to 120 psi.

Metal hose fittings have better durability than plastic barbed hose fittings.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Connect these fittings to air tools for pneumatic applications.

The industry standard for quick-disconnect couplings, these are also known as industrial interchange couplings. Compatible with Industrial-shape plugs and sockets.

These metal hose fittings have better durability than plastic barbed hose fittings. They are 316 stainless steel for excellent corrosion and chemical resistance. Slide the barbed end into hose and secure with a clamp.

Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 6,000 psi

A single rounded bead grips onto hose just like a barb, but has no sharp edges that could cut or damage soft hose. Slide the beaded end into hose and secure with a clamp. Use in coolant applications up to 300 psi.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.