Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

For a strong, secure connection, mount these hangers by welding them to a rod.

Cut as much strap as you need to hang duct, pipe, and other materials.

Route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.

These U-shaped supports allows access to pipe and conduit after installation.

Combine with a U-bolt or routing clamp to convey a variety of material, such as pipe, tubing, and cable raceway, at distance from floors, walls, and ceilings. The extra clearance allows access for maintenance and adding and removing lines.

Attach these light duty hangers to ceilings and walls. They have a stiff wire for supporting suspended ceilings and lighting fixtures.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

These metric Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Grade B16 threaded rods maintain their strength at higher temperatures than Grade B7 threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

These Class 10.9 steel threaded rods are about 25% stronger than medium-strength steel rods.

These are Grade 8 threaded rods.

These steel studs are zinc plated to resist corrosion in wet environments.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

Weld these studs to uncoated steel surfaces.

Also known as dowel screws, use these to join two pieces of wood.

Attach the 90° eye to a surface for support and use the loop to secure the suspended material.

Use the twin hooks to suspend items from two points and use the loop to secure the suspended material. For use with cable trays or signs.

For quick mounting of components, these hangers snap into strut channels for a strong hold and easy repositioning.

For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.