Use hinges to add doors, lids, and machine guards to T-slotted framing.

Provide smooth motion between two pieces of strut channel.

These internally threaded rod ends have an eyelet and a ball that swivels to support angular misalignment. Also known as rod-end bearings.

A PTFE-embedded insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

An oil-embedded bronze insert slowly releases lubricant throughout the life of the rod end.

These internally threaded rod ends have an oil-embedded bronze insert that slowly releases lubricant over time. Connect your grease gun to the fitting to relubricate.

Connect your grease gun to the fitting to lubricate.

Made of cadmium-plated steel, these externally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made to extremely tight tolerances, these internally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Made of stainless steel, these internally threaded rod ends provide excellent corrosion resistance.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

Made of impact-resistant nylon, these internally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

These internally threaded rod ends have an innovative body design that keeps the ball from being pushed out when supporting thrust loads.

Decrease the ID of your rod end to allow approximately 60° of misalignment.

These alloy steel rod end bolts have the highest tensile strength of any fully threaded rod end bolt we offer.

Pivot and hinge components in wet and corrosive environments with these stainless steel or brass rod end bolts.

Create pivoting connections in applications that require high shear strength—the partially threaded shank of these rod end bolts withstands more side force than a fully threaded shank.

With a rubber bushing, these bolts reduce noise and vibration—attach them to rods, pipes, tubes, and cable linkages that have male threading. They’re commonly known as isolated rod ends.

Made of stainless steel, these rod end bolts are stronger and more corrosion resistant than our standard flat-shoulder rod end bolts.

These alloy steel bolts have the highest tensile strength of any blank rod end bolt we offer.

Made of zinc-plated steel or stainless steel, these clevis rod ends offer more corrosion resistance than standard steel clevis rod ends.

Make quick adjustments to these rod ends by inserting and releasing the clevis pins without the need to bend them into place.

Thread or weld the unfinished shank of these rod ends to meet your specific linkage needs.

Able to stand up to frequent use, these linkages offer excellent wear resistance. They consist of ball joint rod ends with a ball stud attached to simplify mounting.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

These internally threaded linkages have an oil-embedded bronze insert that slowly releases lubricant throughout the life of the joint.

Along with excellent wear resistance, these linkages have a grease fitting for easy lubrication.

Use these bent linkages for light duty applications.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel ball joint linkages.

Use these linkages to create inline pivoting connections. They have internal threads on one end and external threads on the other.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

These nylon swivel joints are 80% lighter than steel swivel joints with better corrosion resistance.

Made of stainless steel for excellent corrosion resistance, these nuts make pivoting and hinge movements where misalignment is not a concern.

These hinges are made of metal.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Eliminate slamming lids—these hinges hold lids open at their widest angle and then slowly pull them closed.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Made of plastic with a metal additive, these hinges will set off metal detectors if a piece breaks off and falls into your line.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Also known as bullet hinges, these hinges are the right size for tight spaces and narrow frames.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

Squeeze the hinge handles together to retract the pin and disconnect a door; release the handles and the pin snaps back.

Springs in these hinges without holes automatically swing doors and gates closed behind you.

The springs in these hinges swing doors and gates fully open after a light push on the door.

Use these hinges on lightweight screen and storm doors as well as small gates.

The mounting holes on these hinges form an industry-standard half-moon shape.

These hinges are completely hidden when the door is closed.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

Only one cutout (mortise) is needed to mount these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

A snap-on cover protects these hinges from tampering and creates a finished appearance.

To reinforce loose or damaged hinges, mount one of these hinges to the top edge of the pull-side of the door.

The mounting holes form an industry-standard half-moon shape.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

Plastic bushings on these metal hinges prevent metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the door, these hinges provide a stronger hold than other two-way swinging door hinges.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

A spring in these hinges automatically swings doors and gates closed behind you.

Bearings allow these hinges to open and close doors smoothly.

The hinge pin attaches to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

These hinges have a standard range of motion of 100° to 120°.

Eliminate slamming doors—push the door and these hinges slowly pull it closed.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

To ensure a good fit, these hinges have screws for horizontal, vertical, and depth adjustments after installation.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

Slip the hinge pins into 11/32" Dia. × 5/16" Dp. holes in a cabinet.