For Shaft Diameter For Shaft Diameter |
|---|
|
|
|
OD OD |
|---|
For Housing ID For Housing ID |
|---|
Length Length |
|---|
Flange OD Flange OD |
|---|
Dynamic Thrust Load Capacity Dynamic ThrustLoad Capacity |
|---|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
For Hole Diameter (A) For Hole Diameter (A) |
|---|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Flange Diameter (D) Flange Diameter (D) |
|---|
Hardness Hardness |
|---|
|
About Plain Bearings
More
About Durometer Hardness Scales
More
Easy-Install Dry-Running Flanged Sleeve Bearings
A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Nylon Plastic Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | |||||||||
| 15/64" | 7/32" | 5/16" | 1/32" | 12 lbs. @ 40 rpm | 14 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 00000 |
For 1/4" Shaft Dia. | |||||||||
| 19/64" | 9/32" | 13/32" | 1/32" | 21 lbs. @ 40 rpm | 24 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
For 5/16" Shaft Dia. | |||||||||
| 3/8" | 11/32" | 1/2" | 1/32" | 32 lbs. @ 40 rpm | 35 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
| 3/8" | 15/32" | 1/2" | 1/32" | 43 lbs. @ 40 rpm | 35 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
| 3/8" | 21/32" | 1/2" | 1/32" | 60 lbs. @ 40 rpm | 35 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
For 3/8" Shaft Dia. | |||||||||
| 7/16" | 13/32" | 19/32" | 1/32" | 45 lbs. @ 40 rpm | 49 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
For 7/16" Shaft Dia. | |||||||||
| 1/2" | 15/32" | 21/32" | 1/32" | 60 lbs. @ 40 rpm | 55 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
For 1/2" Shaft Dia. | |||||||||
| 9/16" | 17/32" | 3/4" | 1/32" | 75 lbs. @ 40 rpm | 70 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
| 9/16" | 3/4" | 3/4" | 1/32" | 110 lbs. @ 40 rpm | 70 lbs. @ 40 rpm | White | -40° to 400° | 0000000 | 0000 |
For 5/8" Shaft Dia. | |||||||||
| 11/16" | 15/32" | 15/16" | 1/32" | 85 lbs. @ 20 rpm | 115 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
| 11/16" | 21/32" | 15/16" | 1/32" | 120 lbs. @ 20 rpm | 115 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
| 11/16" | 29/32" | 15/16" | 1/32" | 165 lbs. @ 20 rpm | 115 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
For 3/4" Shaft Dia. | |||||||||
| 13/16" | 25/32" | 1 1/8" | 1/32" | 175 lbs. @ 20 rpm | 165 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
| 13/16" | 1 5/32" | 1 1/8" | 1/32" | 260 lbs. @ 20 rpm | 165 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
For 7/8" Shaft Dia. | |||||||||
| 15/16" | 1/2" | 1 5/16" | 1/32" | 130 lbs. @ 20 rpm | 225 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
| 15/16" | 29/32" | 1 5/16" | 1/32" | 235 lbs. @ 20 rpm | 225 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
For 1" Shaft Dia. | |||||||||
| 1 3/32" | 1 3/64" | 1 1/2" | 3/64" | 310 lbs. @ 20 rpm | 290 lbs. @ 20 rpm | White | -40° to 400° | 0000000 | 0000 |
For 1 1/8" Shaft Dia. | |||||||||
| 1 7/32" | 1 11/64" | 1 11/16" | 3/64" | 390 lbs. @ 10 rpm | 370 lbs. @ 10 rpm | White | -40° to 400° | 0000000 | 0000 |
For 1 1/4" Shaft Dia. | |||||||||
| 1 11/32" | 1 19/64" | 1 7/8" | 3/64" | 480 lbs. @ 10 rpm | 460 lbs. @ 10 rpm | White | -40° to 400° | 0000000 | 0000 |
For 1 1/2" Shaft Dia. | |||||||||
| 1 5/8" | 1 9/16" | 2 1/4" | 1/16" | 700 lbs. @ 10 rpm | 660 lbs. @ 10 rpm | White | -40° to 400° | 0000000 | 0000 |
For 4mm Shaft Dia. | |||||||||
| 5.2mm | 4mm | 7mm | 0.6mm | 7 lbs. @ 120 rpm | 11 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 5mm Shaft Dia. | |||||||||
| 6.2mm | 5mm | 8mm | 0.6mm | 11 lbs. @ 120 rpm | 14 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 6mm Shaft Dia. | |||||||||
| 7.2mm | 6mm | 9.5mm | 0.6mm | 16 lbs. @ 120 rpm | 19 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 8mm Shaft Dia. | |||||||||
| 9.6mm | 8mm | 12mm | 0.8mm | 29 lbs. @ 120 rpm | 22 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 10mm Shaft Dia. | |||||||||
| 11.6mm | 10mm | 15mm | 0.8mm | 43 lbs. @ 120 rpm | 28 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 12mm Shaft Dia. | |||||||||
| 13.6mm | 12mm | 18mm | 0.8mm | 50 lbs. @ 120 rpm | 34 lbs. @ 120 rpm | White | -40° to 400° | 0000000 | 0000 |
For 14mm Shaft Dia. | |||||||||
| 15.6mm | 14mm | 21mm | 0.8mm | 90 lbs. @ 60 rpm | 80 lbs. @ 60 rpm | White | -40° to 400° | 0000000 | 0000 |
For 16mm Shaft Dia. | |||||||||
| 17.6mm | 16mm | 24mm | 0.8mm | 115 lbs. @ 60 rpm | 90 lbs. @ 60 rpm | White | -40° to 400° | 0000000 | 0000 |
For 20mm Shaft Dia. | |||||||||
| 21.6mm | 20mm | 30mm | 0.8mm | 175 lbs. @ 60 rpm | 110 lbs. @ 60 rpm | White | -40° to 400° | 0000000 | 0000 |
For 25mm Shaft Dia. | |||||||||
| 27.4mm | 25mm | 37.5mm | 1.2mm | 215 lbs. @ 60 rpm | 140 lbs. @ 60 rpm | White | -40° to 400° | 0000000 | 0000 |
Shaft Grommets
Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels. All of the grommets are split, which makes them easy to snap into place while also allowing them to expand if they heat up or absorb moisture. Made of plastic, they are chemical resistant and won't dry out and become brittle when exposed to UV rays. All have an extra-hard rating to withstand high levels of impact. They can be used outdoors.
Grommets with MDS reinforcement have added wear resistance.
For technical drawings and 3-D models, click on a part number.
| For Hole Dia. (A) | For Material Thick. (B) | ID (C) | Flange Dia. (D) | Flange Ht. | Overall Ht. (E) | Hardness Rating | Hardness | Temp. Range, °F | For Use Outdoors | Color | Each | |
Nylon Plastic | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 11/64" | 0.072"-0.135" | 1/8" | 3/16", 1/4" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 00000 |
| 15/64" | 0.072"-0.135" | 3/16" | 1/4", 5/16" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 5/16" | 0.072"-0.135" | 1/4" | 11/32", 7/16" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 3/8" | 0.072"-0.135" | 5/16" | 13/32", 1/2" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 7/16" | 0.072"-0.135" | 3/8" | 15/32", 9/16" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 1/2" | 0.072"-0.135" | 7/16" | 17/32", 5/8" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 9/16" | 0.072"-0.135" | 1/2" | 19/32", 11/16" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 11/16" | 0.072"-0.135" | 5/8" | 23/32", 7/8" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
| 13/16" | 0.072"-0.135" | 3/4" | 27/32", 1" | 1/32" | 0.201" | Extra Hard | Rockwell R120 | -40° to 280° | Yes | Blue | 0000000 | 0000 |
Nylon Plastic with MDS Reinforcement | ||||||||||||
| 4.2mm | 1.45mm-2.34mm | 3mm | 4.8mm, 6mm | 0.6mm | 3.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 4.2mm | 2.87mm-3.13mm | 3mm | 4.8mm, 6mm | 0.6mm | 4.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 5.2mm | 1.45mm-2.34mm | 4mm | 5.9mm, 7mm | 0.6mm | 3.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 5.2mm | 2.87mm-3.13mm | 4mm | 5.9mm, 7mm | 0.6mm | 4.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 6.2mm | 1.45mm-2.34mm | 5mm | 6.8mm, 8mm | 0.6mm | 3.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 6.2mm | 2.87mm-3.13mm | 5mm | 6.8mm, 8mm | 0.6mm | 4.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 7.2mm | 1.45mm-2.34mm | 6mm | 7.8mm, 11mm | 0.6mm | 3.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 7.2mm | 2.87mm-3.13mm | 6mm | 7.8mm, 11mm | 0.6mm | 4.2mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 9.6mm | 1.45mm-2.34mm | 8mm | 10.4mm, 13mm | 0.8mm | 3.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 9.6mm | 2.87mm-3.13mm | 8mm | 10.4mm, 13mm | 0.8mm | 4.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 10.6mm | 1.45mm-2.34mm | 9mm | 11.4mm, 14mm | 0.8mm | 3.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 11.6mm | 1.45mm-2.34mm | 10mm | 12.4mm, 15mm | 0.8mm | 3.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 11.6mm | 2.87mm-3.13mm | 10mm | 12.4mm, 15mm | 0.8mm | 4.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 13.6mm | 1.45mm-2.34mm | 12mm | 14.4mm, 17mm | 0.8mm | 3.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |
| 13.6mm | 2.87mm-3.13mm | 12mm | 14.4mm, 17mm | 0.8mm | 4.6mm | Extra Hard | Durometer 75D | -40° to 170° | Yes | Black | 0000000 | 0000 |