A metal shell adds strength.

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.

Good for underwater applications, these bearings won’t swell or warp when wet.

Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Good for underwater applications, these bearings won’t swell or warp when wet.

A metal backing adds strength.

Use these UHMW bearings in wet, corrosive environments.

Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Made of FDA listed PEEK, these bearings are suitable for direct contact with food. The closed backing blocks out dust and other contaminants.

Almost nonabsorbent, these unthreaded LDPE and HDPE spacers won't swell when exposed to water.

Naturally slippery and wear resistant, acetal spacers also offer some resistance to moisture.

Use PEEK spacers as an alternative to metal spacers in high-temperature, high-stress applications. They resist chemicals, wear, and moisture.

Protect components from electrical charges.

Also known as saddle washers, the curved end fits against round objects such as tube and pipe.

Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.

Wings add tension to strengthen the hold in a hole. The other end is releasable for repairs and upgrades.

Secure the self-tapping female connection with a screw; the other end snaps snugly into a panel, yet can be released for repairs and upgrades.

Stick these supports to surfaces where you don't want to drill a hole. The snap-in end can be released for repairs and upgrades.

The extra-tall sleeve extends into holes to provide more protection than other rolled-collar washers.

These washers have a flat bottom and high walls to protect metal screw heads from electrical current.

A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.

Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.

Stainless steel nuts have excellent corrosion resistance in most environments.

Precisely align, level, and adjust spacing on fasteners, shafts, and machinery with these shims, which are color-coded by thickness for easy identification.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Inserts come with a through-hole tap and installation tool.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

The barbed sides keep these securely in place even before a screw is installed.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Install these inserts into plastic parts to create a secure base for fasteners.

Steel inserts have high strength for durability.

Large threads cut into softwood such as particleboard for a strong hold.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

A zinc-plated finish gives these steel inserts mild corrosion resistance.

The male threads on these fittings have a sealant applied for extra leak protection.

Use these fittings in extreme-pressure conditions up to 15,000 psi.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

The male threads on these brass fittings have a sealant applied for extra protection against leaks. Also known as Pressure Class 125 fittings, they are built for use in low-pressure applications.

These brass fittings have the strength to handle high-pressure applications.

Use these heavy-duty brass fittings for high-pressure drinking water applications.

When space in your pipe line is limited, choose these miniature fittings that are one inch or less in length.

Also known as instrumentation fittings, these have the most precise threads and the tightest tolerances of all the brass pipe fittings we offer.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

Their small size makes these miniature fittings a good choice for cramped, confined spaces.

Also known as Pressure Class 3000 fittings, these have the highest pressure rating of all the aluminum pipe fittings we offer.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Connect these fittings to UV-resistant PVC pipe. Designed for outdoor use, they contain an additive that protects against the damaging effects of ultraviolet light. Fittings are typically used in low-pressure residential and commercial plumbing and water supply applications up to 300 psi.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

These fittings are an economical option for chemical waste systems. Fittings are ABS plastic, which has excellent strength and impact resistance and good chemical resistance.

Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.

Attach these fittings to garden hose for a variety of water supply applications. They are metal for better durability than plastic garden hose fittings.

Commonly used in high-pressure welding applications, these nipples connect your tank to the inlet of a pressure regulator. One side has a threaded pipe end and the other side has a rounded end that sits inside a threaded nut to make a threaded connection.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

Press these bumpers into place with the adhesive backing. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. They're comparable to Bumpon bumpers.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

Each hub includes a set screw, which bites into your shaft to hold the coupling in place.

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.