Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

A silicone additive gives this material a self-lubricating surface that reduces friction and extends the life of your parts.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

The addition of MDS gives these tubes exceptional wear resistance along with a self-lubricating surface. They're made of cast nylon 6, making them easier to machine and better electrical insulators than other MDS-filled nylon tubes.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Often used in high-speed, high-precision, and high-impact applications, such as conveyor rollers and bearings, these rods stand up to scratches and scuffs better than our standard UHMW polyethylene rods. Also known as Tivar HPV.

If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.

Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.

Often fabricated into signs, packaging, and light duty housings, polystyrene is easy to thermoform.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Manufactured from Rulon PTFE, a PTFE that's modified with filler material for a super-slippery, impact-resistant surface that resists wear.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Carbon enhances the stiffness of this material, while the addition of PTFE ensures a slippery surface.

Often used in food and pharmaceutical plants, these PEEK rods help you prevent contaminated products from leaving your facility.

Among the strongest plastic materials we offer, Torlon PAI has a slippery surface that resists wear. Use it to make high-friction compressor parts, bearings, and seals.

Stronger and more rigid than Torlon 4301 and 4203 because they’re filled with glass, these Torlon 5030 rods are also electrical insulators like Torlon 4203.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

Use PFA in place of PTFE and FEP for durability in repetitive processes, such as pump parts. It is chemical resistant across a wide temperature range.

Just as chemical resistant as PTFE, yet FEP offers greater impact strength. Use it to make valve components and gaskets.

Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.

This extruded acrylic offers similar performance as cast acrylic at a lower cost.

This extruded acrylic offers similar performance as cast acrylic at a lower cost.

At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

PETG can be formed into complex shapes without sacrificing durability.

Stronger than natural rubber, these polyurethane rods combine the shock-absorbing qualities of rubber with the tear resistance of plastic. Use them to seal narrow spaces such as channels.

Use these polyurethane balls as seals in pumps and check valves or let them bounce inside of vibrating sifters for an effective screen cleaner. They are made of polyurethane, which combines the shock absorbing qualities of rubber with the strength of plastic.

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Using nothing more than standard high-speed steel tooling, Garolite LE can be machined into intricate parts.

A flame-retardant version of Garolite G-11, these tubes are commonly used to make bushings, standoffs, and spacers for areas with high temperatures. All are stronger and resist heat better than Garolite G-10/FR4.

Garolite CE is often fabricated into parts where high strength is not required.

Use Garolite G-10 in place of Garolite G-10/FR4 for applications that are sensitive to halogen, such as in nuclear plants. It's strong, machinable, and electrically insulating.

Choose these Garolite G-7 rods for their high heat tolerance—they withstand temperatures up to 425° F. While not as strong as Garolite G-9, they offer better arc resistance in dry environments.

More electrically insulating than Garolite XX, these tubes are often machined into insulating washers, bushings, transformer spacers, and parts of terminal boards.

Often used in place of aluminum for structural frames, machinery components, and robotics, these tubes are lighter in weight and almost as rigid.

Mount these lightweight tubes to flat surfaces in place of aluminum to create structural frames, machinery components, and robotics.

An alternative to wood in structural applications, FRP fiberglass is strong and lightweight.

Offering excellent arc and track resistance, this GPO3 fiberglass is often used for electrical applications in humid environments.

Hard fiber is the easiest composite to machine, making it good for creating custom parts. Also known as vulcanized fiber.

Neoprene is blended with EPDM and polyethylene for foam tubes that offer good resistance to water, sunlight, and oxidation.

Reduce the chance your concrete will crack from expansion and contraction and other tensile stresses.

This tubing has hard walls like copper tubing, but is lighter in weight and easier to install. It connects to fittings with no heat or soldering required. Tubing meets NSF/ANSI Standard 61 for drinking water.

Excellent strength and durability allow this tubing to handle high-pressure air and water applications up to 950 psi.