We will reply to your message within an hour.
Use where high loads and speeds are not required.
A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.
Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.
Good for underwater applications, these bearings won’t swell or warp when wet.
An aluminum shell adds strength.
Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.
Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.
A metal shell adds strength.
Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.
These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.
Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.
Even in the presence of harsh chemicals and extreme temperatures, these bearings operate under heavy loads and at high speeds.
Use these UHMW bearings in wet, corrosive environments.
Made from slippery materials, these bearings reduce friction without the oily mess.
Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.
These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment.
Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.
Made of acetal with a PTFE filling, these light duty bearings handle speeds twice as fast as standard acetal bearings can.
Made of FDA listed PEEK, these bearings are suitable for direct contact with food. The closed backing blocks out dust and other contaminants.
Embedded lubricant particles increase the load capacity of these bearings while also making them slippery.
These spacers have excellent wear and abrasion resistance. Exposure to moisture may cause them to expand.
Almost nonabsorbent, these unthreaded LDPE and HDPE spacers won't swell when exposed to water.
Polypropylene spacers have a hard surface and resist many chemicals and solvents.
Made of FDA-listed material, these clear spacers can be used in food and beverage applications.
PTFE spacers have a slippery surface and surpass most plastic spacers when it comes to chemical resistance and performance in extreme temperatures.
Naturally slippery and wear resistant, acetal spacers also offer some resistance to moisture.
Use PEEK spacers as an alternative to metal spacers in high-temperature, high-stress applications. They resist chemicals, wear, and moisture.
Cut stock to the length you need.
Also known as saddle washers, the curved end fits against round objects such as tube and pipe.
Also known as shoulder washers.
Also known as shoulder and insulator washers, these nonmetal washers block electrical current and prevent corrosion from mating different types of metal.
Organize your signs and documents by color.
Also known as document protectors, these holders have a hole at the top for hanging.
Wrap the strap of these holders around an object with a 1" dia. or less and secure with the magnetic snaps.
Adhere these holders to a clean, dry surface.
Mount these holders with tape or adhesive.
Stick the adhesive-back bracket to smooth, flat surfaces such as doors, walls, and windows.
Fasten these holders to a surface with screws or nails.
Hooks on the back of these holders allow you to hang them on a nail or screw.
Suction cups allow you to mount these holders to glass and other smooth surfaces.
Draw attention to important signs—these holders have a bright border.
Identify evacuation routes at a glance. Expose these map holders to ambient light and they stay visible in the dark.
The sleeve protects signs and allows you to swap material in and out.
Display a sign even when mounting space is limited. These small holders flex to absorb bumps and have teeth to grip material.
These pouches protect both sides of your sign and are thicker than sheets and rolls for added rigidity.
Peel off the backing and apply these to one or both sides of your sign.
Good for larger signs, peel off the backing and apply these to one or both sides of your sign.
Designed for one-sided viewing.
View signs or documents on both sides of these holders.
These oversized sign holders fit signs up to 36" high. They're often used to display signs on pathways, indoors and out.
Keep tags clean and protected.
These tag protectors have an eyelet in each corner to band them around parts, cables, and other equipment. Insert a tag and then seal the laminating flap to protect the tag from moisture and wear.
Insert a tag and then seal the laminating flap to protect the tag from moisture and wear.
The thin matte surface on these holders reduces glare, making it easier for scanners to read bar codes.
Made of PVC, this sleeving resists chemicals, oil, and acids.
Use this PTFE sleeving in applications where temperatures reach up to 500° F.
Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.
Reduce the likelihood of slipping in high-traffic areas. This sleeving has thick, nonslip fibers that create friction so it doesn’t slide when you step on it. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.
Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Tightly braided nylon fibers give this sleeving excellent abrasion resistance. As it wears, the fibers frizz and make the outer wall thicker for improved protection.
Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.
A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.
Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.
Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.
Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.
Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.
The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.
Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.
Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.
Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.
A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.
Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.
The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.
A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.
Wrap this sleeving around cable, cords and wires to protect them and to form bundles.
Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.
This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.
Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.
Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.
Use this general purpose tubing to insulate and protect wire and cable.
This tubing creates a tight seal over irregularly shaped objects.
Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.
The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.
Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.
Identify ground wire with this green-and-yellow striped tubing.
Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.
Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.
Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.
This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.
Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.
Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.
After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.
Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.
With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.
This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.
With excellent resistance to tears and cuts, this tubing withstands demanding use.
Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 5,000 volts.
A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.
Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.
Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.
Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.
Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.
Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.
Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.
Keep general purpose tubing in a variety of sizes on hand.
Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.
A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.
Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this wrap has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.
Close these tubes with a cap on each end.
These tubes have one sealed end and one end that closes with a cap.
Because of their square shape, these tubes can be stacked, and the flat surface is easier to label than a round surface.
These tubes are easier to label and stack than round tubes. To adjust the length, push the ends of the tube together or pull them apart.
Adjust these tubes by twisting the two halves. A hexagonal end prevents rolling.
Shield shafts and threaded parts from abrasion and chipping.
These sleeves contain a corrosion inhibitor to shield metal parts from corrosion.
These are thicker and more rigid than standard document protectors.
Protect sets of documents or thick instruction manuals.
These binders mount to machines, equipment, and walls.
Display documents on a desktop or other flat surface using these binders, which have a sanitary design.
Mount these binders to machines, equipment, walls, and flat surfaces to create permanent viewing spots and free up desk space—they display documents in a way that’s sanitary for all users.
Place these on top of a machine or table, then relocate them as you see fit.
Use these sleeves alone or with gloves to protect your arms.
These single-use gloves prevent cross contamination and provide the dexterity needed for intricate work.
Handle food without contaminating it. Made with metal additives, these gloves will be caught by metal detectors if they fall into a batch—helping you comply with Hazard Analysis and Critical Control Point (HACCP) programs.
Handle small items when dexterity is essential and full hand coverage isn't needed. These single-use cots cover fingers without restricting hand movement.
Protect your shirt sleeves from stains and wear in food-processing environments.
Comfortable and flexible, these fabric gloves are good for parts handling, maintenance, fabrication, and other general purpose applications.
The all-leather design offers durability and wear resistance.
The coating on these gloves provides extra protection without limiting dexterity. It also provides a secure grip.
A magnetic pad holds fasteners and small metal parts on the back of your hand while you work. The palm of these gloves has a textured polyurethane coating that provides extra grip, yet is thin enough for assembly work, small parts handling, and operating touch-screen devices.
Minimize hand fatigue while operating rivet guns, jackhammers, and other power tools that produce high levels of vibration.
Keep fingerprints and other contaminants off of parts during inspections.
Use these gloves to avoid damaging static-sensitive electronic parts.
Operate touch-screen devices without removing your gloves. A coating on the palm adds wear and abrasion resistance.
Reduce fatigue during jobs that require you to perform the same hand motions over and over. The open-finger style keeps your fingers free to grip objects.
Use these gloves to cover your hands while leaving your fingers open to grip objects.
Protect your hands while working with petroleum-based products. These gloves safeguard hands from cold objects as well as cold weather.
The lining withstands intermittent heat, while the outer layer of material acts as a barrier to chemicals and solvents.
Also known as wave solder gloves, wear these to avoid damaging static-sensitive electronic parts. They have a nitrile coating that protects hands while soldering.
Keep hands warm in temperatures as low as -320° F without sacrificing dexterity. These gloves can be used to handle dry ice.
Maintain a secure grip on wet surfaces. These gloves have a lining that safeguards hands from cold objects as well as cold weather.
Designed for intermittent handling of hot pipes, engine parts, and castings, these gloves protect your hands from moderate heat and some abrasion.
Wear these gloves to keep your hands dry and warm at temperatures as low as -320° F.
Made of aluminized fabric, these gloves reflect radiant heat and protect against sparks.
These mitts can be worn as mitts or open-fingertip gloves. A fleece lining keeps your hands warm when working with cold objects or in cold weather.
Prevent cross-contamination when handling objects that many people touch.
Protect objects in your clean room from skin oil and other contaminants when dexterity is essential and full hand coverage is not needed.
The coating on these gloves provides extra grip and protection without limiting dexterity. A fluorescent yellow back side makes them easy to spot.
ASTM D120 rated for use when handling live electrical equipment, these gloves come tested and marked with the test date. All gloves meet NFPA 70E for protection against arc-flash hazards.
Often used when cleaning machinery, tools, and other equipment with harsh solvents and degreasers.
Cleaned and bagged in environments with low levels of particulates, these powder-free, unlined gloves won't contaminate your work area.
Wear as a liner or over other gloves to protect against esters as well as aromatic, chlorinated, and oxygenated solvents such as ketones and alcohols.
Protect your hands from oil, acids, and scrapes while you're working.
Often used for cleaning lab spaces, these gloves withstand most acids, alcohols, and cleaning solutions.
Safeguard hands from cold objects as well as cold weather. These gloves remain flexible in low temperatures, have a thermal liner, and are rated for cut resistance.
These gloves conform to your hand for improved dexterity. Use them on machine assembly jobs where protection from oil and cuts is essential.
Bumpers on the back of these gloves protect your hands from impact when working in confined spaces. These gloves are rated for cut resistance to protect hands from sharp objects.
For applications that require frequent glove changes, the sleeves stay connected to the glove box so you can quickly change the size or type of glove being used.
The accordion design prevents the sleeve from collapsing and allows more air circulation. It stays connected to the glove box so you can quickly change the size or type of glove being used.
Use these gloves in glove boxes to safely handle hazardous substances or avoid contaminating sensitive materials. Seamless one-piece construction provides maximum strength and integrity.
Sized specifically to adapt standard shaft collars to pipe, these bushings create a tight fit.
Apply heat and these grommets shrink around wire, cable, and cords to keep out dust, debris, and moisture.
Carry pens, pencils, and small tools in these protectors while shielding pockets from stains and damage.
Retain glass when tubular bulbs break; these guards have a solid lens.