Use sun energy to bring light to remote areas and storage spaces without electrical wiring. These lights come with a solar panel to recharge their battery. Simply connect the lights to the panel and place the panel in full sunlight to charge. To power the battery faster, you can also plug these lights into a charger using the included USB cable. A USB output port allows you to power other smart devices and accessories with these lights, as well.

All lights have built-in LEDs that last longer, are more efficient, and generate less heat than other light technologies. They cast a neutral light appearance that’s often found in workspaces. An impact-resistant plastic lens protects the LEDs. You can dim these lights to conserve battery life. To use them as a security light in unsupervised areas at night, set them to auto mode—they’ll turn on automatically in the dark or when they detect motion.

Use the included mounting holes and brackets to secure these lights permanently to the wall, or hang them temporarily with the included fold-out D-rings. The solar panel also has a mounting bracket to secure the panel to horizontal and vertical surfaces. It’s adjustable, so you can rotate and tilt the panel to achieve the best angle for maximum sunlight exposure.

These floodlights have heads that swivel and rotate for perfect positioning in hard-to-light areas. Their built-in LEDs last longer, are more efficient, and generate less heat than other light technologies. They cast a cool light that highlights white/blue tones, which is good for inspecting. You can control them remotely with your Bluetooth-enabled smartphone.

Style A has a built-in handle and a removable carrying strap.

Style B has a retractable handle and wheels for easy transport. In addition to cordless operation, this floodlight can be plugged in. Batteries must be charged with the case lid open.

This IP67 rated light withstands temporary submersion in a maximum of one meter of water for up to 30 minutes. It's compact for easy transport to job sites with no electrical power. With a head that adjusts up and down, it floods your job site with light. It has a hook and a magnet for mounting, so you can keep your hands free for other work. This light has built-in LEDs that last longer, are more efficient, and generate less heat than other light technologies. It has a durable tempered-glass lens to protect the LEDs.

Note: Battery life is significantly reduced when lights are used at the high-beam setting.

The handle on this floodlight also acts as a stand—pivot it 360° to aim light where it's needed. This floodlight is small and easy to carry to job sites that don't have electrical power service. It has built-in LEDs that last longer, are more efficient, and generate less heat than other light technologies. They cast a cool light that highlights white/blue tones, which is good for inspecting. This light has an impact-resistant plastic lens to protect the LEDs.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces. They turn on when they detect motion. These lights use a built-in LED bulb that lasts longer, is more efficient, and generates less heat than alternatives.

The solar panel is separate from style A, B, and C lights, so you can place the panel in direct sunlight while mounting the light in a shaded area. Even though they’re detached from the panel, these lights have an integrated sensor that prevents them from turning on during the day.

The solar panel is built into the top of style D, E, and F lights, so there’s no need to run wire between the two. These lights must be mounted in the sun so they can charge during the day.

Style E and F lights are protected from low-pressure jets of liquid such as water from a garden hose.

Connect the battery pack to your existing fluorescent light to convert it into an emergency backup light. They include a test switch to check that the bulbs and battery are working properly.

Kits that cannot be sold to the regions listed are resitricted by local energy efficiency requirements.

Lights that cannot be sold to California or Oregon are restricted due to energy efficiency requirements.

When the power goes out, these lights go on. These backup lights have built-in LEDs so they last longer, are more efficient, and generate less heat than other technologies. Rated for use in damp locations, these lights withstand exposure to humidity and moisture. Lights can be hardwired to operate on any of the voltages listed. They have a low-voltage disconnect so they won’t drain the backup battery. Use the test switch to check that the heads and battery are working properly. Heads adjust to any angle to direct light where needed.

Lights with a plastic housing resist corrosion better than lights with a steel housing.

Lights with a steel housing are more durable than lights with a plastic housing. Mount add-on heads in remote areas to extend emergency lighting. Wire up to three of these heads to your emergency backup light.

Rated NEMA 4X, these lights are protected from corrosion and washdowns. They have built-in LEDs so they last longer, are more efficient, and generate less heat than other technologies. Lights can be hardwired to operate on any of the voltages listed. They have a low-voltage disconnect so they won’t drain the backup battery. Use the test switch to check that the heads and battery are working properly. Heads adjust to any angle to direct light where needed.

Mount add-on heads in remote areas to extend emergency lighting. Wire up to three of these heads to your emergency backup light.

Mount add-on heads in remote areas to extend emergency lighting. Hardwire each head to an emergency backup light; they operate on any of the voltages listed. These add-on heads have built-in LEDs so they last longer, are more efficient, and generate less heat than other technologies. Rated for use in damp locations, these heads withstand exposure to humidity and moisture. Heads adjust to any angle to direct light where needed.

No need for wiring—these lights plug-in with a two-prong plug. When the power goes out, these lights go on. They have a low-voltage disconnect so they won’t drain the backup battery. The built-in LEDs last longer, are more efficient, and generate less heat than other types of lights.

Use the test switch to check that the heads and battery are working properly. Heads adjust to any angle to direct light where needed.

These lights are UL listed for Class I, Division 2, Groups A, B, C, and D, and Class II, Division 2, Groups F and G for use in environments where ignitable concentrations of hazardous material occur infrequently, such as in the case of an accidental spill or failure of a ventilation system. They withstand acetylene, hydrogen, ethylene, propane, carbonaceous dusts, and nonconductive dusts. Lights can be hardwired to operate on any of the voltages listed. They have a low-voltage disconnect so they won’t drain the backup battery. Use the test switch to check that the heads and battery are working properly. Heads adjust to any angle to direct light where needed. They cannot be sold to California, Vermont, or Oregon due to energy efficiency requirements.

Direct light where it’s needed with this pivoting-head flashlight. When plugged in, it will automatically light up if the power goes out. With long-lasting, built-in LEDs, this flashlight is more efficient and generates less heat than flashlights with other light technologies. It casts a bull’s eye beam pattern, which has a bright center that reaches long distances. This flashlight has a flat bottom, so you can work hands-free without it rolling away. It's IP04 rated, so it withstands liquid splashed from all angles. It cannot be sold to Canada due to energy efficiency requirements.

Note: Battery life is significantly reduced when flashlights are used at the high-beam light setting.