Power Source Power Source | Show |
---|
|
Capacity Capacity |
---|
|
Maximum Stroke Length Maximum Stroke Length |
---|
|
Ram Type Ram Type |
---|
|
Ram Return Operation Ram Return Operation |
---|
|
Plug Type Plug Type |
---|
|
Overall Height Overall Height |
---|
|
|
|
Frame Material Frame Material |
---|
|
Hydraulic Oil Included Hydraulic Oil Included |
---|
|
These presses have a control lever to advance and return the ram. Adjust the table height with the removable table pins. Mobil DTE 24 or equivalent hydraulic oil is required (sold separately).
Table | Ram | Overall | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Cap., lbs. | Max. Stroke Lg. | Clearance Over Table | Travel | Lg. | Wd. | Material | Dia. | Ram Hole Thread Size | Ht. | Wd. | Dp. | Power, hp | Voltage | Plug Type | Includes | Each | |
Fixed Ram | |||||||||||||||||
20,000 | 10" | 40" | 36" | 20" | 8 1/2" | Steel | 1 3/4" | 1"-8 | 80" | 29 3/4" | 24" | 1 | 120V AC | Three Prong | Hydraulic Pump with Fittings, Pressure Gauge | 00000000 | 000000000 |
50,000 | 10" | 44" | 36" | 28" | 9 1/8" | Steel | 3" | 1 1/2"-6 | 88" | 37 1/2" | 30" | 1 | 120V AC | Three Prong | Hydraulic Pump with Fittings, Lifting Chain, Pressure Gauge | 00000000 | 00000000 |
Also known as a 40-ton metalworker, this hydraulic machine handles a variety of forming tasks including pressing, punching, notching, and shearing. The safety guard complies with ANSI B11.5 standards. Machine requires 1 gallon of Mobil DTE 24-SSU or equivalent hydraulic oil (sold separately).
Overall | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Cap., lbs. | Throat Dp. | Ht. | Wd. | Dp. | Steel Thick. for Pressing | Steel Rod Dia. for Shearing | Sheet Metal Size for Shearing, Thick. × Wd. | Power, hp | Voltage | Plug Type | Cord Lg., ft. | Each | |
80,000 | 3 3/4" | 55 1/4" | 30" | 24" | 3/8" | 3/4" | 3/8" × 4", 1/4" × 6" | 3/4 | 120V AC | Three Prong | 5 | 00000000 | 000000000 |
Sheet Metal Size for Shearing | |||
---|---|---|---|
Thick. | Wd. | Each | |
1/4" | 8" | 00000000 | 0000000 |
For Notch | ||||
---|---|---|---|---|
Lg. | Wd. | Ht. | Each | |
1 3/4" | 2" | 1/4" | 00000000 | 0000000 |
Economy Benchtop Drill Presses | Replacement Spring Cap Assembly | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Max. Workpiece Dia. | Max. Table Cap., lbs. | For Max. Drill Bit Size for Cast Iron | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Key Included | No. of Speeds | Spindle Jacobs Taper No. | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Motor Current, A | Wt., lbs. | Each | Each | ||
120V AC—Single Phase | ||||||||||||||||
Jacobs Spindle Shank | ||||||||||||||||
10" | 70 | 1/2" | 1/2" | 3,070 | Yes | 5 | 33 | __ | 2 1/2" | 1/3 | 4.1 | 70 | 00000000 | 0000000 | 00000000 | 000000 |
13 1/4" | 80 | 1/2" | 1/2" | 3,350 | Yes | 16 | 33 | __ | 3 1/4" | 1/3 | 6 | 120 | 0000000 | 000000 | 0000000 | 0000 |
120V AC/240V AC—Single Phase | ||||||||||||||||
Morse Spindle Shank | ||||||||||||||||
15" | 100 | 5/8" | 5/8" | 3,450 | Yes | 16 | __ | 2 | 5" | 1/2 | 7.3 | 150 | 0000000 | 00000000 | 0000000 | 00000 |
Replacement Spindle Assembly for Drill Presses with Morse Spindle Shanks | 0000000 | Each | 0000000 |
To accommodate large, odd-shaped pieces of material, the head of this drill press moves 12" forward and backward. It also tilts 45° left and 90° right (as viewed when facing the drill press).
For Max. Drill Bit | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Max. Workpiece Dia. | Max. Table Cap., lbs. | Size for Steel | Size for Cast Iron | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Key Included | No. of Speeds | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Motor Current, A | Wt., lbs. | Each | |
120V AC—Single Phase | ||||||||||||||
Morse Spindle Shank | ||||||||||||||
33" | 70 | 3/8" | 5/8" | 5/8" | 3,500 | Yes | 5 | 2 | 3 5/32" | 1/2 | 4.8 | 100 | 0000000 | 0000000 |
Use for drilling small holes. A sensitive belt-drive motor reduces drill breakage and damage.
Max. Workpiece Dia. | For Max. Drill Bit Size for Steel | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Manufacturer | No. of Speeds | Spindle Jacobs Taper No. | Spindle Travel | Motor Power, hp | Motor Current, A | Wt., lbs. | Each | |
120V AC—Single Phase | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Jacobs Spindle Shank | ||||||||||||
7" | 1/8" | 1/8" | 20,000 | Albrecht | Variable | 0 | 1 1/2" | 1/5 | 2 | 25 | 0000000 | 000000000 |
Lock the magnet to secure the base and then move the motor to center the cutter for pinpoint accuracy. You can move the motor 3/4" forward and backward and tilt it 20° left and right. Switch these drills from forward to reverse without stopping—ideal for both drilling and tapping applications (not recommended for use with pipe taps). In addition, a dial lets you adjust the speed to match your application, making these great for drilling hard materials at slow speeds. Base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill point breakaway) is calculated against a 1" thick steel plate. Drills include a spoked feed handle that mounts on either side.
Drill presses for 3/4" and 1 1/4" max. drill bit sizes can be used with carbide-tipped hollow-core cutters.
Drill press for 1/2" max. drill bit size cannot be used with hollow-core cutters. It is not for use with 5/8"-11 and 1/2"-13 taps.
Note: To avoid damaging the electromagnet, do not mount press to a base that has a welder already grounded to it.
O'all | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Drill Bit Size | For Max. Cutter Dia. | For Max. Bit Shank Size | For Max. Tap Size | Max. No-Load Speed, rpm | Spindle Morse Taper No. | Spindle Travel | Holding Force, lbs. | For Min. Surface Thick. | Lg. | Wd. | Ht. | Wt., lbs. | Manufacturer Model No. | Specifications Met | Each | |
120V AC | ||||||||||||||||
Chuck Spindle Shank | ||||||||||||||||
3/4" | 2 1/4" | 3/4" | 1"-14 | 350 | __ | 11" | 1,600 | 1/2" | 17" | 7 1/2" | 32 1/2" | 70 | 4206-1 | UL Listed | 0000000 | 000000000 |
1/2" | __ | 1/2" | 5/8"-18 | 600 | __ | 11" | 1,600 | 1/2" | 15 1/4" | 7 1/2" | 29 1/2" | 60 | 4204-1 | UL Listed | 0000000 | 00000000 |
Morse Spindle Shank | ||||||||||||||||
1 1/4" | 2 1/4" | __ | 1"-14 | 750 | 3 | 11" | 1,600 | 1/2" | 17" | 7 1/2" | 32 1/2" | 70 | 4209-1 | UL Listed | 0000000 | 00000000 |
1 1/4" | 2 1/4" | __ | 1"-14 | 500 | 3 | 11" | 1,600 | 1/2" | 17" | 7 1/2" | 32 1/2" | 70 | 4208-1 | UL Listed | 0000000 | 00000000 |
Switch these drills from forward to reverse without stopping—ideal for both drilling and tapping applications (not recommended for use with pipe taps). In addition, a dial lets you adjust the speed to match your application, making these great for drilling hard materials at slow speeds. Base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill point breakaway) is calculated against a 1" thick steel plate. Drills include a spoked feed handle that mounts on either side.
Drill presses for 3/4" and 1 1/4" max. drill bit sizes can be used with carbide-tipped hollow-core cutters.
Drill press for 1/2" max. drill bit size cannot be used with hollow-core cutters. It is not for use with 5/8"-11 and 1/2"-13 taps.
Note: To avoid damaging the electromagnet, do not mount press to a base that has a welder already grounded to it.
O'all | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Drill Bit Size | For Max. Cutter Dia. | For Max. Bit Shank Size | For Max. Tap Size | Max. No-Load Speed, rpm | Spindle Morse Taper No. | Spindle Travel | Holding Force, lbs. | For Min. Surface Thick. | Lg. | Wd. | Ht. | Wt., lbs. | Manufacturer Model No. | Specifications Met | Each | |
120V AC | ||||||||||||||||
Chuck Spindle Shank | ||||||||||||||||
1/2" | __ | 1/2" | 5/8"-18 | 600 | __ | 9" | 1,600 | 1/2" | 14 1/2" | 7 1/2" | 25 1/2" | 50 | 4202/4253-1 | UL Listed | 0000000 | 000000000 |
3/4" | 2 1/4" | 3/4" | 1"-14 | 350 | __ | 9" | 1,600 | 1/2" | 16 1/4" | 7 1/2" | 27" | 65 | 4210-1 | UL Listed | 0000000 | 00000000 |
Morse Spindle Shank | ||||||||||||||||
1 1/4" | 2 1/4" | __ | 1"-14 | 750 | 3 | 9" | 1,600 | 1/2" | 16 1/4" | 7 1/2" | 27" | 65 | 4202/4292-1 | UL Listed | 0000000 | 00000000 |
1 1/4" | 2 1/4" | __ | 1"-14 | 500 | 3 | 9" | 1,600 | 1/2" | 16 1/4" | 7 1/2" | 27" | 65 | 4202/4297-1 | UL Listed | 0000000 | 00000000 |
Select from a number of speeds by repositioning the drive belt before starting the drill press.
Multispeed Economy Floor Drill Presses | Replacement Spring Cap Assembly | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Max. Workpiece Dia. | Max. Table Cap., lbs. | For Max. Drill Bit Size for Steel | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Key Included | No. of Speeds | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Current | Wt., lbs. | Each | Each | ||
120V AC/240V AC—Single Phase | |||||||||||||||
Morse Spindle Shank | |||||||||||||||
15" | 100 | 5/8" | 5/8" | 3,450 | Yes | 16 | 2 | 5" | 1/2 | 7.3A | 165 | 0000000 | 000000000 | 0000000 | 000000 |
17" | 100 | 5/8" | 5/8" | 3,450 | Yes | 16 | 2 | 5" | 1 | 10A | 180 | 0000000 | 00000000 | 0000000 | 00000 |
120V AC—Single Phase | |||||||||||||||
Morse Spindle Shank | |||||||||||||||
20" | 65 | 1" | 3/4" | 4,200 | Yes | 12 | 3 | 4 3/4" | 1 | 13.5A | 315 | 00000000 | 00000000 | 000000 | 00 |
Turn the dial on this drill press while it is running to get the optimum speed for your job. A laser projects a crosshair at the point of bit contact and a digital readout displays the spindle speed.
Max. Workpiece Dia. | Max. Table Cap., lbs. | For Max. Drill Bit Size for Steel | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Current | Wt., lbs. | Each | |
120V AC/240V AC—Single Phase | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Morse Spindle Shank | |||||||||||
18" | 88 | 5/8" | 5/8" | 3,000 | 2 | 6" | 1 | 15A | 245 | 0000000 | 000000000 |
To accommodate large, odd-shaped pieces of material, the head of this drill press moves 12" forward and backward. It also tilts 45° left and 90° right (as viewed when facing the drill press).
For Max. Drill Bit | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Max. Workpiece Dia. | Max. Table Cap., lbs. | Size for Steel | Size for Cast Iron | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Key Included | No. of Speeds | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Current | Wt., lbs. | Each | |
120V AC—Single Phase | ||||||||||||||
Morse Spindle Shank | ||||||||||||||
33" | 50 | 3/8" | 5/8" | 5/8" | 3,500 | Yes | 5 | 2 | 3 5/32" | 1/2 | 4.8A | 150 | 0000000 | 0000000 |
The weight and rigidity of these presses prevent vibration so you can maintain close tolerances for high-quality metal drilling. Turn the dial on these drill presses while they are running to get the optimum speed for your job.
Drill presses with 20" max. workpiece diameter have a safety guard that swings away for easy tool changes.
Max. Workpiece Dia. | Max. Table Cap., lbs. | For Max. Drill Bit Size for Steel | For Max. Bit Shank Size | Max. No-Load Speed, rpm | Chuck Key Included | No. of Speeds | Spindle Morse Taper No. | Spindle Travel | Motor Power, hp | Current | Wt., lbs. | Each | |
120V AC—Single Phase | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Morse Spindle Shank | |||||||||||||
18 1/8" | 200 | 1 1/16" | 3/4" | 1,200 | Yes | Variable | 3 | 5 3/8" | 2 | 6.8A | 675 | 000000 | 000000000 |
120V AC/240V AC—Single Phase | |||||||||||||
Morse Spindle Shank | |||||||||||||
20" | 300 | 7/8" | __ | 2,000 | Yes | Variable | 3 | 6 1/2" | 1 1/2 | 17.9A | 590 | 0000000 | 00000000 |
240V AC—Three Phase | |||||||||||||
Morse Spindle Shank | |||||||||||||
20" | 300 | 7/8" | __ | 2,000 | Yes | Variable | 3 | 6 1/2" | 1 1/2 | 17.9A | 590 | 0000000 | 00000000 |
440V AC—Three Phase | |||||||||||||
Morse Spindle Shank | |||||||||||||
20" | 300 | 7/8" | __ | 2,000 | Yes | Variable | 3 | 6 1/2" | 1 1/2 | 17.9A | 590 | 0000000 | 00000000 |
Optional Morse Taper Arbor with Drill Chuck for 20" Floor Drill Presses | 0000000 | Each | 0000000 |
These drills work with hollow-core cutters to cut only on the periphery of the hole and produce a solid slug. This allows for a faster and easier cut than drilling with standard drill bits. Also known as magnetic core drilling machines.
They have a feed handle that mounts on the left or right side of the drill. The electromagnetic base attaches to flat ferrous surfaces (such as steel and cast iron).These drills also have a valve to adjust coolant flow. Holding force (also called drill-point breakaway) is calculated against a 1" thick steel plate.
Chucks and adapters (sold separately) allow these models to accept standard drill bits.
O'all | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Cutter Dia. | For Cutter Shank Size | Max. Cutting Dp. | Spindle Travel | Max. No-Load Speed, rpm | No. of Speeds | Current, A | Holding Force, lbs. | For Min. Surface Thick. | Coolant Included | Lg. | Wd. | Ht. | Wt. | Manufacturer Model No. | Each | ||
120V AC | |||||||||||||||||
A | 1 3/8" | 3/4" | 2" | 5 11/16" | 590 | 1 | 9.5 | 2,810 | 1/2" | No | 10 1/4" | 3 1/2" | 19 3/4" | 25.8 lbs./sq. ft. | JME Holemaker III | 0000000 | 0000000 |
B | 1 1/2" | 3/4" | 2" | 2 9/16" | 480 | 1 | 9.4 | 650 | 3/8" | No | 13 5/8" | 7 7/8" | 17 5/8" | 32 lbs. | JHM USA101 | 0000000 | 00000000 |
C | 2 9/16" | 3/4" | 2" | 5 11/16" | 520 | 2 | 12.6 | 3,080 | 1/2" | No | 20 1/4" | 9 7/8" | 23 5/8" | 35.5 lbs. | JCM 256 U | 0000000 | 00000000 |
1 gal. Cutting, Tapping, and Threading Coolant for Styles B and C | 0000000 | Each | 000000 |
1.6 oz. Cutting, Tapping, and Threading Coolant for Styles B and C | 0000000 | Each | 0000 |
1/2" Chuck and Adapter for Jancy Magnetic-Base Drills JHM USA101 | 0000000 | Each | 000000 |
5/8" Chuck and Adapter for Jancy Magnetic-Base Drills JCM 256 U | 0000000 | Each | 000000 |
These drills work with hollow-core cutters to cut only on the periphery of the hole and produce a solid slug. This allows for a faster and easier cut than drilling with standard drill bits. Also known as magnetic core drilling machines.
They have a feed handle that mounts on the left or right side of the drill. The electromagnetic base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill-point breakaway) is calculated against a 1" thick steel plate.
O'all | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Cutter Dia. | For Cutter Shank Size | Max. Cutting Dp. | Spindle Travel | Max. No-Load Speed, rpm | No. of Speeds | Current, A | Holding Force, lbs. | For Min. Surface Thick. | Coolant Included | Lg. | Wd. | Ht. | Wt., lbs. | Manufacturer Model No. | Each | ||
120V AC | |||||||||||||||||
A | 1 1/2" | 3/4" | 2" | 2" | 450 | 1 | 8 | 995 | 3/8" | Yes | 11 5/8" | 7 3/4" | 19 5/8" | 30 | HMD904 | 0000000 | 0000000 |
B | 2 3/8" | 3/4" | 3" | 3" | 450 | 2 | 12.5 | 1,290 | 3/8" | Yes | 12 7/8" | 8 1/4" | 25 7/8" | 50 | HMD917 | 0000000 | 00000000 |
240V AC | |||||||||||||||||
B | 2 3/8" | 3/4" | 3" | 3" | 450 | 2 | 6.3 | 1,290 | 3/8" | Yes | 12 7/8" | 8 1/4" | 25 7/8" | 50 | HMD917 | 0000000 | 00000000 |